Model #66513469K900 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Fill, Drain, And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Lower Washarm Parts
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Dishwasher not starting

A:

I can understand your frustration over your dishwasher failing to start. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
May 28, 2013
A:

I must assume that you have a voltage meter and know how to use it safely when checking live voltages. You did not indicate where you checked the voltage supply at. The voltage supply to the dishwasher should be verified at the control board. There should be 2 wires supplying voltage to the control board. One wire is Tan in color and it will be connected to P8 terminal, the other voltage supply is connected to P2-6 and it will be Black with a White stripe. You will need to check voltage at these two wires to the White wire connected to P7 connector. If 110-120vac is verified at these two points the most likely failure is the interface board. If voltage is not present at either one, check the thermal fuse. One end of the Black wire with White stripe will connect to the thermal fuse. If the thermal fuse is open the dishwasher will be dead.

I recommend calling a service technician to diagnose and repair your dishwasher. Sears Home Service

Read More
Jerome G. - Personal Solutions Manager -
Sears Technician
May 29, 2013
See more answers
Q:

Appliance manuals and ages

A:

Here is the manual for the microwave: Kenmore Microwave 401.80089700 Owner's Manual . That model began production in 2008 but it is still a current model.

Here is a link for the manual on the range: Kenmore Range 790.77469802 Owner's Manual . That model of range began production in 2010 and it is also still a current model.

The number that you provided for the dishwasher appears to be a part number. I did not find information for that appliance using the number that you provided. I recommend that you check the model number sticker again for a model number that begins with 665. . . or 587. . . You may also see other 3 digit prefixes such as 465. . . That dishwasher model number label should be on the side of the dishwasher door or the side of the opening to the dishwasher tub. Reply with that updated model number and we should be able to provide the manual and date of production for that dishwasher.

Read More
Lyle W -
Sears Technician
May 25, 2012
A:

Thanks - I was finally able to get back into the house. The dishwasher's correct model number is 665.13469K900. I found the manual online, so I don't need that, just the years of production.

Read More
Keri -
June 01, 2012
A:

Hello Keri. Thanks for adding that model number for the dishwasher. That dishwasher began production in March of 2009.

Read More
Lyle W -
Sears Technician
June 04, 2012
See more answers
Q:

dishwasher drains slowly.

A:

Dishwasher's are the best appliance in the whole world so when it starts to have problems it can get really disappointing. While you are waiting on an expert to answer your question, I found this great link in the Manage My Life website. I have attached the link below. Hope this helps!

Read More
Dezeray S -
January 25, 2011
A:

From the description you give I suspect the drain pump is the problem.

The other suspect would be the drain hose loop with check ball on the left hand side of the unit. See the 1st image below. You will have to pull the dishwasher out to access this hose.

The usual way to check this problem is to remove the drain hose from under the sink. Put it over a pan and initiate a drain cycle. You may have already done this since you know it is draining slowly.

The problem will be a clog in the sump or hoses or with the pump.

The image below will show how to access and remove the drain pump.

I hope this information is helpful to you. You can reply with any additional details for further assistance.

The drain pump 661662 can be obtained from the following link: Sears PartsDirect .

Read More
Fred M -
Sears Technician
January 26, 2011
See more answers

Top Parts