Model #66513462K902 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel And Latch Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Fill, Drain, And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Model 665.13462k902 won't run a full cycle. 66513462K902 Kenmore Undercounter dishwasher

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your dishwasher. Upon researching model 66513462K902; it sounds like you may need to replace the control board. The control board controls the cycles of the dishwasher so when it fails the unit will not successfully complete its cycles. I have posted a link of the control board to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
April 12, 2015
Q:

the clean light keeps blinking even with the door open or reshut or ajar on my dishwaher. Can you tell me why and why its not shutting off? 66513462K902 Kenmore Undercounter dishwasher

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear of the issue you’re having with the clean light not turning off on the dishwasher. I know how frustrating issues like this are.

The control board is programmed to stop the current cycle and not allow any further cycles if it suspects a faulty heating element (no increase in water temperature during the water heat intervals). The control will cause the clean light to blink 7 times in a repetitive fashion and disable the Start/Resume key until cleared.

To clear and reset the control board press the following keys in this order: Heated Dry, Normal, Heated Dry, Normal and the dishwasher will begin to operate. Let it run for one (1) minute and then press the Cancel/Drain button an allow it to complete the drain cycle. You will be able to program and start the dishwasher again now. It can fail again and blink the clean light if the heating element fails to heat up the water again. It could have a failed heating element or the Neutral door switch is not closing when the door is shut.

If the steps above do not work then I believe console assembly will need to be replaced.

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-469-4663, or click here to be directed to the page to set up service.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
December 23, 2014
Q:

Why is light on control panel not working? 66513462K902 Kenmore Undercounter dishwasher

A:

Thanks for the inquiry and for being a valued member.

We won't be able to nail it down as to whether it's the board or the control panel. The components will need to be tested with a meter to be sure. In situations such as this, we recommend having a service technician involved to help make the diagnosis/repair more efficient.

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-469-4663, or 
click here to be directed to the page to set up service.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
October 18, 2014

Top Parts