Model #66513193K900 KENMORE ELITE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Fill, Drain And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump, Washarm And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

Kenmore Dishwasher - 66513193K900 - Not Completing Cylce on Heated Dry 66513193K900

Q:

Leaking 66513193K900 Kenmore Elite Dishwasher

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your dishwasher. Upon researching model 66513193K900; I recommend that you check the float to make sure it is working as the unit fills. If the float is ok then you may need to replace the overflow switch, the over flow switch works with the float to make sure that the unit does not over flow. To replace the overflow switch or to remove it make sure you unplug the dishwasher power cord.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

I trust this information will help you, we appreciate your business thank for choosing Sears.

27”

Read More
CarlosZ -
Sears Technician
August 13, 2015
Q:

Three year old Kenmore dishwasher 66513193K900. At the end of the run, dishes look Ok but bottom has soap suds that go away after an hour.

A:

I know that it can be very frustrating to have issues with your dishwasher. I suspect a build up of calcium deposits in inside the pump causing the problem. We should be able to solve the problem without taking the pump apart. I recommend running the dishwasher thru a quick rinse with some vegetable oil. Vegetable oil breaks up soap and will not harm the dishwasher. Next, do a through cleaning of the dishwasher, using a product called Dishwasher Magic. This product is sold in most supermarkets. Just follow the directions on the bottle. Also, too much rinse aid can cause suds. I recommend using the factory default setting of 2 for the rinse aid. I hope this helps. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
October 23, 2013
A:

Our rinse aid is not full. I ran a cycle with vegetable oil and it did not help. I used the Dishwasher magic and it has not helped at all. Any other suggestions?

Read More
Prabodh -
October 29, 2013
A:

These are all the normal reasons for the unit to have suds in the bottom: Using too much detergent for the type of water conditions (if you have a water softener use less detergent) Wrong kind of detergent (I recommend Cascade powder) Rinse agent leaking into the wash/rinse water (look for a trail of rinse agent under the dispenser assembly) Rinse agent set to dispense too much rinse agent Value branded detergent (buy name brands) Dishwasher not filling with enough water Pre-rinsing dishes Using one of those rinse aide baskets hung from the rack. Soft water It is possible that the dispenser is not opening at the right time during the cycle. Let all of the suds go away, then run one cup of white vingear through the unit. Make sure the unit is empty when you do this. After this is complete ran a normal wash cycle (with dishes), but do not add the detergent to the dispenser, place it in the bottom of the unit. If there are not suds at the end of the cycle the dispenser is the issue. If there are, then I would suggest checking all of the things listed above. Please let me know if there is anything else you need. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
October 29, 2013
A:

Your analysis was excellent. We used vinegar and it did not help. We looked at the Rinse aid dispenser and the setting was 2. We reduced it to 1 and the suds decreased. We then let the rinse aid run out and the suds stopped. We refilled the rinse aid and the suds have returned. The setting is still only 1. When we washed dishes without rinse aid they did not look good and were staying wet with droplets. Does this mean that the rinse aid is leaking?? What do we do. Thanks.

Read More
Anonymous -
November 11, 2013
A:

To fix this you will need to replace the rinse aid dispenser. This is not an easy thing to do, and it will require taking apart the whole door. I would recommend you schedule service for this.

Read More
AnneJ -
Sears Technician
November 11, 2013
See more answers

Top Parts