Model #66513122K702 KENMORE ELITE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Fill, Drain And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump, Washarm And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

Lower Spray Arm Not turning on Dishwasher 66513933K013 66513933K013

A:

Thank you for choosing SearsPartsDirect. I can certainly understand how frustrating it can be when your dishwasher spray arm is not working properly. I did look into the model number you have provided and I have found information to assist you. 


Most dishwashers lower spray arms are powered by the water going through the pump assembly. I would recommend checking the wash impeller & sump housing.


Click here for information. 

May I ask is your unit getting water? Is the spray arms getting water?

You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .


Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
June 26, 2014
A:

The unit is getting water. The upper spray arm and spinner are working fine. Does this model have a separate flow control for the lower wash arm.

Read More
Paul -
June 26, 2014
A:

There is a diverter valve motor. Click here to view.

Read More
Natasha12 -
Sears Technician
June 26, 2014
A:

How would I know if it is not working?

Read More
Paul -
June 26, 2014
A:

How would I know if it is not working?

Read More
Paul -
June 26, 2014
A:

 To test the diverter valve you would do a resistance check at the main control board. Disconnect the P7 connector and check from pin 4 blue to pin 6 blue. The resistance reading that you should get is between 1300 and 1600 ohms. If not within this range then the motor is faulty and would need to be replaced. 
'

You will need an OHMs meter.

Read More
Natasha12 -
Sears Technician
June 26, 2014
A:

Is there a schematic showing the location of what you described?

Read More
Paul -
June 26, 2014
A:

Additionally can the diverter motor be replaced with the unit still installed under the counter or does the unit have to be pulled out to access the motor.

Read More
Paul -
June 26, 2014
A:

Additionally can the diverter motor be replaced with the unit still installed under the counter or does the unit have to be pulled out to access the motor.

Read More
Paul -
June 26, 2014
A:

I went right past this advice. When you say check...I would recommend checking the wash impeller & sump housing, what does that mean?

Read More
Paul -
June 26, 2014
See more answers
Q:

Correct wiring for dishwasher door latch micro swith 665.13122k702

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
May 12, 2014
Q:

Kenmore 665.13122K702 dishwasher not always draining

A:

Thank you for your question and I understand your concern.

If you're hearing the drain pump running and it's not draining, then I suspect it could be caused from using too much detergent or the check valve in the drain hose could be sticking shut. If the detergent is causing too much suds, the pump will not be able to pump out all the water. So make sure you're not using too much detergent causing a suds issue. Now, if you do not hear the drain pump running when it should, there could be a loose wire connection in the drain pump circuit.

The diverter valve would not have anything to do with it draining nor would the OWI.

There is a check valve in the L-connector that possibly could be sticking closed at times preventing the water from passing out of the drain pump. During drain, the water flows through the center of the filter cup, down and out the drain opening.

I recommend removing the lower access panel and use a pair of channel lock pliers to squeeze the clamp that secures the drain hose to the drain outlet. Pull the clamp and hose off the drain outlet. Look in the end of the L-connector and make sure the check valve moves to the open position and is not sticking shut. Be sure and drain all the water out before removing the drain hose from the drain pump. NOTE: Disconnect the power supply from the dishwasher before servicing. 

Have some old towels handy to soak up any remaining water that will likely pour out the end of the drain hose and drain pump.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.
 
 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
December 03, 2013
A:

It's not too much detergent. I have very few suds if any at all. I use the hard tablets in the dispenser. I got the L-connector off, but the check valve must be around the corner of it. I can't reach it. When I stick my finger in it, there is rubber coming off making a mess. Do I stick something in there to clean it?

Read More
Jen -
December 03, 2013
A:

Jen; You can try sticking something in there. You should be able to feel and possible see the check valve. If not, it may have broken loose and is stuck in the drain hose somewhere. You may have to remove the drain hose and attempt to clear it out or just replace the drain hose.

Read More
Joey S -
Sears Technician
December 03, 2013
A:

Thank you Joey. There is absolutely nothing in the L-connector or the hose as far as I can see. If it is rubber like the rest of the connector, it may have almost just disintegrated. The rubber is flaking off as I touch it and I can see what looks like flakes of it in the drain hose. Sounds like this is the problem and I will be ordering a new drain hose!

Read More
Jen -
December 03, 2013
A:

Jen: The check valve is likely causing the intermittent draining issue. Replacing the drain hose will most likely resolve the issue.

Read More
Joey S -
Sears Technician
December 05, 2013
See more answers

Top Parts