Model #6630 CRAFTSMAN Sharpener

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

2 Touchpad model numbers MEW6630DDS19 Maytag 30

Q:

Maytag double oven model MEW6630DDB will preheat but won't maintain the temperature to bake. MEW6630DDB

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

I recommend going through the diagnostics to get an error code.

To access the diagnostics on the ATM style control: 
Access the SETUP menu and scroll down until the SERVICE option is displayed. 
Scrolling is accomplished by tapping the control area to the right of the up and down 
arrows displayed on the control. 
Select the SERVICE option by tapping the control area to the left of the word service. 
While the information on where to call for service is displayed, press and hold the BACK 
and ENTER buttons for three seconds.

Usually it is the high limit thermostat keeps the correct temperature. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 13, 2015
A:

I do not see a SETUP button or menu. Where is it located?

Read More
Ann -
July 13, 2015
A:

Which part number is the "high limit thermostat"?

Read More
Ann -
July 13, 2015
See more answers
Q:

Problem with Maytag Double Oven

A:

Thank you for your question.  I am sorry for the problem with your Maytag MEW6630DDB Built-in Wall Oven.  The error codes should be different from the E01 you discribe.  My first suggestion is you check the images below.  The first image tells how to enter and run a diagnostic test.  The 2nd image contains a list of codes you might see.  I hope this helps.  You can reply below with any additional details for further assistnace.  The main control may be at fault but first try the test and see if any other codes are displayed. 

Read More
Fred M -
Sears Technician
November 04, 2013
A:

Thank you for your question.  I am sorry for the problem with your Maytag MEW6630DDB Built-in Wall Oven.  The error codes should be different from the E01 you discribe.  My first suggestion is you check the images below.  The first image tells how to enter and run a diagnostic test.  The 2nd image contains a list of codes you might see.  I hope this helps.  You can reply below with any additional details for further assistnace.  The main control may be at fault but first try the test and see if any other codes are displayed. 

Read More
Fred M -
Sears Technician
November 04, 2013
A:

Fred M, Thank you for this information. I didn't get the diagnostic test to tell me anything. It's possible that this is because the problem is intermittent, or it's possible the system didn't really enter a diagnostic mode. Upon holding the two buttons down, it did beep three times - perhaps to indicate it was entering the mode or perhaps to say - hey, let go of my buttons. Any other thoughts or suggestions? The oven is about 6 to 7 years old.

Read More
Jeff -
November 07, 2013
A:

If the unit will not enter the diagnostic test then there may be a problem with the control or the keypad. All of the keypad selections should work. Can you select all cycles and option or do some keypads not respond?

Read More
Fred M -
Sears Technician
November 11, 2013
A:

All of the buttons were responding, however, intermittently it would turn off, and it wouldn't be an oven. I decided to replace the control board, and did so. This seems to have solved the problem, and now it's clear that the control display is much brighter. It also now enters a diagnostic mode when pressing the appropriate buttons. Thanks for your assistance, I hope this resolves it. There were more inputs to the control board than I expected - 12 bundles of wires - yikes.

Read More
Jeff -
November 11, 2013
A:

It is always a good idea to use your cell phone camera to take a picture of any connections. It is also good practice to mark wire colore and where it goes before removing any wires. Remember to turn the power off first.

Read More
Fred M -
Sears Technician
November 12, 2013
See more answers