Model #6500 DEK Generator

  • Air Filter/alternator/battery
    3 Results
  • Control Panel/choke Module
    3 Results
  • Engine/exhaust Pipe Module
    3 Results
  • Fuel Tank/main Breaker/muffler
    3 Results
  • Oil Switch/recoil Starter/wheel Kit
    3 Results
Find part by diagram >

Question and Answers

Q:

why does my whirlpool cabrio washing machine keep getting an unbalanced load error

A:

I see your washer machine keeps on giving you Unbalanced load error code. While you are waiting on an expert to answer your question. I found this really great link on why your washer has Unbalanced load error. I attached the link below. Hope this helps!

Read More
Dezeray S -
August 31, 2010
A:

An item stuck between the spin basket and the outer tub of the washer could be causing this problem. With the washer empty and turned off, see if the spin basket will rotate freely by hand. If you detect some resistance or suspect that there is an item stuck between the spin basket and the outer tub, you can unplug the washer and pull the basket out of the washer as shown in the first image provided below.

If your washer has an agitator instead of an impeller like the one shown in the first image below, you will need to use the procedure in the second image to pull the spin basket out (with the washer unplugged ).

If you find no problems with an item being stuck between the basket and the tub, then you could have a problem with the shaft that sticks up from the bottom of the washer tub. If you need more help, submit additional details and the full model number of your Cabrio washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 01, 2010
A:

See images below for the above answer.

Read More
Lyle W -
Sears Technician
September 01, 2010
A:

ok I just had this problem with this and my washer was progressivly giving me the unballanced load called my repair guy and he said it was probbaly the suspension rods the washer has 4 of them and they work like shocks for the tub and if they go bad than they allow the drum to spin wildly. we replaced the suspension rods and bingo the washer was working like new.

Read More
charlie -
March 13, 2013
A:

Thanks Charlie. I am glad that you pointed out that failure and fix. In some situations, the suspension rods can apparently cause the unbalanced problem in that type of washer. That information can help other readers who face the same problem.

Read More
Lyle W -
Sears Technician
March 14, 2013
A:

I have a Whirlpool Cabrio WTW6500WW1 that keeps kicking the UL error code as well. It is only 4 years old. In doing some online research I was seeing so many people suggest changing the suspension rods. So I replaced all 4 and I am still getting the error. We did not see anything stuck in between the basket and outer tub. I called a local service company and they suggested that maybe it is the bearings. Any other suggestions? Thoughts?

Read More
Amie -
November 15, 2013
A:

When the machine reaches the Spin cycle is stopped I did with the empty washing machine is showing error UL

Read More
Juan P -
February 27, 2014
A:

I have a Whirlpool Cabrio WTW6500WW1 the machine reaches the Spin cycle is stopped I did with the empty washing machine is showing error

Read More
Juan P -
February 27, 2014
A:

I'm having similar issue with cabrio wtw6600sw2, UL error with nothing in machine. I just did a bearing seal replacement, basket is spinning freely, there is no bouncing or excessive movement, but get UL on spin cycle. At drain & spin get UL at 9 minutes. Now if I lean the machine back against the wall as if to work on it underneath, it works. Now I just tried med speed spin cycle and it worked, got uL on high speed, med worked 3 x's now......Confussed

Read More
gary -
January 06, 2016
See more answers
Q:

Craftsman Garden Tractor DGS 6500 with Kohler 26 HP engine and hydrostatic transmission is suffering from a loss of drive.

A:

It can be frustrating when your very expensive lawn tractor isn't working properly. I researched your question and found two links that may help you diagnose the problem, if not an expert will respond shortly. I have provided the link below. I hope this helps!

Read More
Jacqueline S -
August 05, 2010
A:

If you can't push the tractor with the freewheel lever pulled out the brakes might be sticking.

If you can push the tractor and the wheels turn pull the freewheel lever out and let it return sharply 6-8 times. Spray the area around where the freewheel linkage connects to the transaxle liberally with WD40 or something similar.

I am sending you an image showing the process of purging the transaxle.

Read More
Jimmy K -
Sears Technician
August 05, 2010
A:

Can you resend the purging process in the Email above? Thanks!

Read More
Bruce -
December 13, 2015
See more answers
Q:

Bosch Dryer WTMC6500UC-01 - E01 error often. NOT an airflow problem WTMC6500UC-01

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

Normally there is lint that will build up in the blower housing. I would recommend in removing the back panel and cleaning that blower housing out. Your error code should go away.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
JeffwallaceIII -
Sears Technician
December 17, 2014
A:

I also have this problem and it is not an airflow problem.I suspect it is the temperature sensor. There are 2 components in the front of the unit where the lint filter seats. I'm not sure which one is the correct sensor. Part numbers & descriptions on the diagram are 42221 (Sensor ntc) and 422273 (Limiter te). Seems like 422221 is the right one, but can you tell me for sure? Once I've identified the part, is there a way to test it to see if it is in fact defective? Thanks.

Read More
Michael -
December 04, 2015
See more answers