Model #6461069902 CRAFTSMAN Buffer/polisher

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

polishing pad's 6461069902 Craftsman Buffer/polisher system

A:

Thanks for the inquiry and for being a valued member.

The new pads for this polisher are part number 41P27400. They are available for purchase on Sears Parts.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
July 26, 2015
Q:

SPECIFICATIONS 6461069902 Craftsman Buffer/polisher system

A:

Thank you for the inquiry and for using SearsPartsDirect.com.

Unfortunately, due to the age of this particular buffer/polisher, I don't have access to the manual or any documentation for it. I was able to find a buffer/polisher with a similar model, but it appears to be newer and not really the same design.

I have provided a link below that you may click on to be directed to view the manual if you would like, but I didn't see anything in regards to the RPM rating.

I will forward your model to our archives to see if we still have the hard copy or microfiche for manual part number 58-006 on model 6461069902. I checked online as well, but didn't see anything for it. If I get any response from archives, I will reply back to this thread and update you accordingly. 

Thanks for the inquiry and for using SearsPartsDirect.com. 

Read More
Jeff Wallace Sr -
Sears Technician
August 26, 2013
A:

Thank you for your question. I will be happy to assist you. I looked up the model number you submitted. This model buffer/polisher is a random orbital model. This means it will move back and forth and turn. If the pad does not have any resistance, it will spin but as soon as you put it on the car, the pad will move back and forth. The manufacture does not state the rpm because it is not made to spin on the car. I hope this is helpful. Please let me know if you need further assistance. Thank you for using Manage my life. Mark.

Read More
Mark T -
Sears Technician
August 28, 2013
A:

Can you repost the link for this manual? Thank you,

Read More
Sebastian -
November 22, 2013
A:

If you will note the bottom line under the model number it states the "rpm/min " It Reads 2400 OSC/MIN... I would hazard a guess and say that means oscillateing per min...

Read More
tim -
November 22, 2013
A:

Thanks for the inquiry Sebastian and for using SearsPartsDirect.com.

We were not able to get the model specific manual for the model number in question, but I do have a link for some related manuals for the buffer/polisher below. Just click the link to be directed to the page.

Craftsman Buffer/Polisher Manuals

Let us know if we can be of any further assistance and thanks for using SearsPartsDirect.com.  

Read More
Jeff Wallace Sr -
Sears Technician
November 23, 2013
See more answers
Q:

How to install Pad on Padholder Assembly for a Buffer/Polisher system

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina F. -
October 22, 2011
A:

Thank you for your question on how to replace the buffer pad to the polisher system.

You can use 3M product contact cement 77.

I have given you a picture below.

You will need to pull and cut the old pad off the base. Usually a slow steady pull will remove the old pad with the help of a putty knife.

Make sure to remove all the foam so the base is clean and dry.

After removing the old pad clean both surfaces with alcohol and let dry.

Spray each piece with 3M 77 and let it set tack until when you touch it with your finger it does not stick.

Then make sure you align it carefully and apply the pad to the base of the buffer.

It is not permanent and you will be able to remove if you do it carefully.

I hope this information will help.

Sam A.

Read More
Sam A -
Sears Technician
October 24, 2011
A:

Thank you very much Chuck

Read More
Chuck -
January 18, 2013
See more answers