Model #64 COMMODORE Computer

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

update for the Kenmore Elite Ergo 3

A:

The ManageMyLife website is a great place to find answers to questions that need qualified and insightful responses. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner. I have provided a link below that you may find interesting until your expert can respond.

Read More
James -
August 24, 2012
A:

I can understand how helpful it is to have the right information for your sewing machine. Just click on this link to download the Version 2 manual that you need: Ergo Version 2 Manual . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
August 24, 2012
A:

I dont need the manual, I need the actual update

Read More
pam -
August 25, 2012
A:

I also need the update, as well as an instruction sheet for attaching the different sewing feet.

Read More
Billie -
July 28, 2014
A:

I also need the update, as well as an instruction sheet for attaching the different sewing feet.

Read More
Billie -
July 28, 2014
A:

I would like to get a software update for my Kenmore ergo 3 19010 preferably for windows 8

Read More
Katrina -
November 23, 2014
A:

Katrina - If you are looking for compatibility with Windows 8, it seems that you are looking for an update to the Customizer software and not the firmware for the machine itself. To get the Customizer software to work on Windows 8, do the following: Instructions for getting 19010 Customizer Ver. 1.0 (93300) to work on a Windows 7 or Windows 8 PC. 1. Insert the 19010 Customizer software installation disc into your CD drive on your PC. 2. In Windows Explorer, go to This PC (or My Computer). 3. Right-click on the DVD drive with the disc, and select Open to view the files on the disc. 4. Right-click SETUP.EXE and select Properties. 5. In the Properties window, select the Compatibility tab. 6. In the Compatibility mode area, check "Run this program in compatibility mode for:". 7. Select Windows XP (Service Pack 2) in the drop-down menu. 8. Click OK. 9. Double-click SETUP.EXE to install the software, following the prompts. 10. Shortcuts for two programs will be installed on your desktop: Customizer 19010 EasyImport and Customizer 19010 EasyEdit 11. For each of these shortcuts, right-click the shortcut, select Properties, and repeat steps 5 through 8. You should now be able to run each of the programs by double-clicking on the shortcuts.

Read More
Anonymous -
April 03, 2015
A:

We have a 10 year old 19010. We have 15 Scandisk memory cards (64mb and up) with thousands of patterns on them that suddenly don't work in the machine. After inserting one of the cards the message reads 'if you continue all memory will be lost' or 'the memory card will be erased'. This just happened. The only pictures that I can retrieve are the ones that are in the original memory bank of the sewing machine and they work fine. I am unable to access any of my saved patterns on my Memory cards. Any ideas how this can be resolved? I have sent the machine out twice and both times they were not able to solve the problem. The last time I was told that I probably needed a new motherboard for it, but they were not certain and they were unclear as to whether the parts were available. I can't buy the disks anymore and can't find any way to retrieve the information on them or anyway to use that information in my sewing machine. Any ideas?

Read More
edda -
October 05, 2015
A:

i also need an update for my kenmore elite ergo 3 embroidery/sewing machine model 19010 (385.19010200). I had to get a new computer with with MS 10. I use my sewing machine and embroidery machine often and now can not use the embroidery part of the machine machine. I can not load the disc on my new computer. Please help. Thanks

Read More
Claudia -
January 23, 2016
See more answers
Q:

size 795.71053.012

A:

The cubic feet for model 795.71053012 are:
Freezer   8.82
Refrigerator   18.82
Overall   27.64

Read More
Ernest7574 -
Sears Technician
November 10, 2015
Q:

Replace Water Line on LG Refrigerator

A:

Replacing parts on appliances can be quite a mystery without instructions. While you are waiting on an expert to answer your question, a suggestion I have is to add model number to this thread so you can get a better answer from the experts!

Read More
Dezeray S -
January 11, 2011
A:

I am trying to get that clarified...(it's my neighbor's). The number she gave me was LGC26905TT. I'm not finding that number anywhere. She is supposed to be getting back to me and I'll post it as soon as I have it. I didn't know if all LG's had the same set-up or not.

Read More
Jaybop -
January 11, 2011
A:

The model number is LSC26905TT. I think the part I need is 616F. It is the larger tube on the back. It looks fairly straight-forward, but didn't want to get it apart and find any surprises when I went to connect the tube. It looks like other folks have had problems with holes in this tubing?

Read More
Jaybop -
January 11, 2011
A:

Thanks for providing that updated model number and the part that you are trying to replace. You can order new tubing from the Sears PartsDirect website.

I recommend that you repair this failure by cutting the ends of the water line at the top and the bottom outside of the area where it is leaking. Use some fittings (John Guest fittings) to splice in a replacement line of tubing. Be sure that you shut off the water supply and unplug the refrigerator when completing this repair.

You should be able to find fittings to splice the water line into place at your local hardware or plumbing supply store.

If you were to replace the whole part, you would need to pull the cover shown in the first image below. After removing the screw, you will need to release the tabs that are shown in the second image. You can then remove the cover. The third image shows the water lines going into the refrigerator cabinet with that cover removed. The lines go into the refrigerator cabinet and connect to the filter housing (Key 626A in the 4th image). You will need to disconnect that line and connect the new one. To access that housing, you will need to remove the light bulb cover, light bulbs and control housing in the top of the refrigerator cavity. The other end of the line that you are replacing is probably hooked to the inlet water valve assembly shown in the 5th image. The 6th image shows how to remove that component. You can see that replacing that entire water line can be an extensive project. That is why I recommend splicing in a replacement run of tubing.

Be careful when working with the water lines. Failure to properly connect the water lines can result in a leak that will cause damage to flooring or counters.

If you need more help, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 12, 2011
A:

Here are the additional images.

Read More
Lyle W -
Sears Technician
January 12, 2011
A:

Hi Lyle.. I have a question regarding the valve. I've posted a question already ..but have not heard anything.. I have and LG25950 and it has stopped making ice. per biker mike (expert) here he replied to another person saying that the water valve might be frozen. I've moved the refrig, and can see the valve, but don't know what to do next or how to remove it.. He also mentioned to flush the line.. before hooking it up and again... I don't know how.. could you assist me ?

Read More
Lori -
March 31, 2011
A:

The water valve itself is probably not frozen. The water tube that fills the ice maker could be frozen. I read the answer that Expert Jimmy provided for your question. He provides some good information. See if the ice maker has ice cubes in it. I provided some technical information about that ice maker in the image below. You can manually cycle the ice maker by pressing and holding that fill adjustment button for 3 deliberate seconds. See if you can get the ice maker to cycle in this manner. If not, then the ice maker module will probably need to be replaced. If the ice maker cycles but does not fill, you could have a problem with the water valve. You would need to determine whether the water valve is getting voltage during the fill portion of that manual cycle process. I recommend that you have a technician check this type of problem. That type of diagnosis will require a live voltage check using a volt/ohm meter. Those types of checks are dangerous. I provided a link for the Sears Service website below this reply. If you decide to have the refrigerator serviced, you can use that link to schedule a technician. If you want to continue to troubleshoot and repair this problem yourself, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
April 01, 2011
A:

Lyle W , the line on the back of my lg French door refer also had a pin hole leak. I repaired that section of line. Another pin hole developed in the old line. I'm stumped. What is causing this? The first hole developed almost immediately after we changed the filter. Could that have done something to the pressure? Lfx25960st

Read More
Dan -
January 23, 2012
A:

Hello Dan. Changing that filter would not affect the water pressure through those water lines in a manner that would cause a leak. It could be a coincidence that the leak occurred immediately after changing that filter. You may want to shut off the water supply and remove the water supply line on that back of the refrigerator. Place the end of the water supply line in a bucket and check the water pressure and flow from the end of that water supply line. The water pressure inside the refrigerator will not be more than what you see from the end of that water supply line. If that water pressure is normal then I don't think that a water pressure problem is causing your leaks. That being said, there is a chance that the water supplier was conducting some maintenance or repairs on the water supply in your area and that the system experienced a temporary spike in water pressure. You can check on that issue. If you do not find excessive supply pressure, then the water line failures were likely caused by a failure or fatigue of the water lines. I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 23, 2012
A:

Thanks Lyle W. I Would like to change that entire line. The bottom is easy, but the top enters the back of the refer into styrofoam. Can you explain how to disconnect the top end? It must connect to the filter, but I do not know how to access that point. Any help is appreciated. Dan LG. Lfx25960ST

Read More
Dan -
January 23, 2012
See more answers