Model #629.46779 MAYTAG Ranges, Electric

  • Top Assembly
    3 Results
  • Internal Controls
    3 Results
  • Body
    3 Results
  • Body (serial Prefix 11)
    3 Results
  • Oven/base
    3 Results
  • Oven/base (serial Prefix 12)
    3 Results
  • Door/drawer
    3 Results
  • Door/drawer (serial Prefix 11)
    3 Results
  • Door/drawer (serial Prefix 12)
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

Replace Heating Element in a Kenmore range.

A:

I know this type of information can be very helpful for you to have.  While you are waiting for your expert answer, I did some research on the part.  I was unable to locate information that would be helpful with regards to your question at this time.  Your expert will answer within two business days.  Thank you for using Manage My Life.

Read More
Yadira B -
May 01, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. The heating element has mounting screws secure to the back of the oven cavity. Just unscrew the mounting screws and then pull the element out. Reverse these instructions to reinstall the element. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

 

Read More
Tykara -
Sears Technician
May 02, 2013
See more answers
Q:

Help for a slide in range?

A:

Good morning....I can appreciate your being able to work with the panel for a while and now it has failed completely. It may be the electronic control board failing but there may be other possibilities as well. I have provided a link below that will go into more detail on the subject. Also keep in mind that an expert on that model number will investigate the matter further. They will get back to you within the next two business days if not sooner. I hope this assists you in resolving you display panel issue and have a nice day.

Read More
Henry -
December 03, 2012
A:

Your current problem (with the control not powering up unless turn on one of the burners) is likely caused by a voltage supply failure. The wiring diagram for your range is shown in the image below. The green line on that diagram shows the normal voltage supply for the control board. That wire traced in green is probably black in color. It is likely that you are missing that leg of power to the control board. The red line on that diagram traces the voltage path that is apparently causing the control to light up when a burner is turned on. The L2 leg of power is applied to the L1 circuit through the burner switch and the element as shown in that diagram. I recommend that you check the house circuit breakers for the range. You may find that one of those breakers is tripped. Some houses have fuses instead of breakers. If you can restore that power to the range, then the stove top elements should heat properly. If the control for the oven still does not work properly after restoring power, then you may have a problem with the electronic control board on that range. That electronic control board is no longer available as a replacement part. If it needs repair, it would need to be sent to a Core Centric Solutions for repair. Here is a link for the website for that company that has contact information: CoreCentricSolutions.com . The cost for repairing that type of electronic control board is normally around $150. Be sure that you shut off the house circuit breakers for the range before accessing internal components and removing that control board.

These tips may help you fix this range problem on your own. If you need more help, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 05, 2012
See more answers
Q:

oven continues to heat after setpoint is reached

A:

I can see your concern when there is a problem with controling the temperature on the Kenmore range. The link below is on a similar issue which may be helpful while an expert responds to your specific model.

Read More
Anna T -
November 11, 2012
A:

Thanks Anna T The info found following that link you posted is along the vein of what I'll need. I'll await the reply of an expert.

Read More
roger -
November 11, 2012
A:

There is a chance that you could have received a defective relay control board. Before you exchange or return that relay control board, I recommend that you check the resistance of the oven temperature sensor probe circuit. That temperature sensor probe circuit is traced in purple on the wiring diagram in the first image below. The second image shows the temperature/resistance chart for that sensor. The third image shows how to access the electronic control board in the console. At room temperature of 75 degrees, you should measure around 1091 ohms through that sensor circuit. If the resistance through that sensor circuit is off, then you can check the resistance of that sensor directly at the component. The 4th image shows how to access that oven temperature sensor probe. If that sensor is bad, then it will need to be replaced. You can order parts from this page: Kenmore Range Model 629.46779 Parts .

If the sensor is okay, then you could have a failure in the relay control board or in the electronic oven control board. I don't have specific tests for those two control boards to narrow down the cause of your failure.

I hope that this additional information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 13, 2012
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
November 14, 2012
See more answers