Model #62945775 KENMORE Free Standing, Electric

  • Top Assembly
    3 Results
  • Body
    3 Results
  • Oven/base
    3 Results
  • Door
    3 Results
  • Wiring Information
    3 Results
  • Top Assembly (series 11)
    3 Results
  • Top Assembly (series 12)
    3 Results
Find part by diagram >

Question and Answers

Q:

Urgent-Replacement Part Doesnt Fit Appliance

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

 

Read More
Joseph P. -
June 15, 2013
A:

Model # of the Stove is 62945775, the replacement part thru your company for the ceramic cooktop ONLY is 12001850, which is a substituted part from the original replacement #Main top PART NUMBER: 74004372 Substitution: 12001853 Learn why BUT it doesnt fit- the welded brackets on the inside top of the replacement lid DO NOT line up correctly with the welded brackets inside the actual stovetop- what can be done???

Read More
April -
June 15, 2013
A:

The 12001853(white) part number and the 12001850 (black) are the same replacement tops just one is white and the other black- we have the black part #

Read More
April -
June 15, 2013
A:

I can understand how important it is to have the right parts for your range. On this model the cooktop has been change to the 12001853 cooktop kit. This kit, however should have come with two sets of brackets for the installation. There is one set of brackets that are longer then the others to make sure they can line up with the ones on the range. If you don't have these, then I would suggest contact our Parts department and set up an exchange for the full kit. If you do have them, then you should be able to attach the cooktop. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 16, 2013
See more answers
Q:

What does "F1" error code mean on my electric Kenmore rage?

A:

The "F1" code could indicate a failed oven control or possibly a bad sensor. The "F1" fault code could also have another digit displayed along with the "F1" which would indicate a different failure.

I added the technical data sheet in the image below that will have the explanation of the other possible codes. I recommend calling a service technician to diagnose and repair your range.

Read More
Joey S -
Sears Technician
July 28, 2009
A:

i cant check to see if ny other code # s hd to turn off breake as range just gets hot right away

Read More
Barbara -
April 15, 2013
See more answers
Q:

Does anyone know how to replace a temperature sensor on a digital Kenmore oven?

A:

Having to work on your oven can be challenging. Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide the detailed model number so your expert will be able to provide you the best possible answer. Just click on reply below and the provide the required data.

Read More
Priscilla V -
September 19, 2012
A:

Model number: 62945775

Read More
Vernon -
September 19, 2012
A:

Hello Vernon. Thanks for adding that model number. The first image below shows how to access the oven temperature sensor probe in that range. Shut off the house circuit breaker for the range before accessing internal components. You did not mention the specific symptoms of your problem (whether the control works and whether the elements heat at all). If you are not certain that the oven temperature sensor is causing that problem, then you can test that sensor using a volt/ohm meter as described in this previous answer: How to test oven sensor. . That sensor should measure around 1091 ohms at 75 degrees (room temperature). There is a temperature resistance chart in the second image. If the sensor is okay, then you may want to re-install that sensor and measure the resistance of the entire sensor circuit from the digital clock control board in the console. The third image shows how to access that control board in the console (with the circuit breaker for the range still shut off ). The 4th image shows the wiring diagram for that oven control board. If you measure the correct resistance through that entire sensor circuit from the control board then the sensor is apparently not causing your oven heating failure. You could have a problem with the clock control board in that range in that situation (depending on your exact symptoms). Reply with additional details if you need more help diagnosing this failure.

You can order parts from this page if necessary: Kenmore Range Model 629.45775 Parts . As noted above, be sure that you shut off the house circuit breaker for the range before accessing internal components .

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 20, 2012
A:

Here is the 4th image that shows the wiring for that control board in the console. NOTE: If the control does not even power up, you may have a tripped hi-limit switch on the power supply wire to the control. That component is shown on the wiring diagram.

Read More
Lyle W -
Sears Technician
September 20, 2012
A:

Basically what happened, my wife ran the self-clean with no issue. Afterwards, she tried to bake something and the digital display read 100 degrees; however, the element never got warm (bake and broil). The digital display shows an "F1" code. I have tried unplugging the range and plugging it back in, and I have turned off the circuit breaker for an hour and turned it back on. The stove top operation works fine.

Read More
Vernon -
September 20, 2012
A:

Also, when she tried to bake something and set the temperature for 350 degrees, the display reverted back to 100 degrees.

Read More
Vernon -
September 20, 2012
A:

Hello Vernon. I posted an image below that shows a field test for that range. Try to use that test to check the temperature sensor reading and the last fault code recorded on the range. Look for the sub fault code in the display. Reply with that information and we will assist you further.

Read More
Lyle W -
Sears Technician
September 20, 2012
A:

I followed the steps you sent me, and I got an "F1-2" code. Which the chart says "Over temp while cleaning". This makes sense since the oven quit working after my wife did the self-clean. My next question is what needs to happen now in order to get the oven working again?

Read More
Vernon -
September 20, 2012
A:

You indicated that you already disconnected electrical power to the range and the powered it back up. Try that process again to reset the control but leave the power off for 5 minutes. That may reset the code so that the control board will work properly. Check the current temperature that the sensor is detecting. If that sensor is still detecting high resistance or the control board is showing that it still detects a high temperature, then that code will not clear.

Read More
Lyle W -
Sears Technician
September 21, 2012
See more answers

Top Parts