Model #629.45769 MAYTAG Ranges, Electric

  • Top Assembly
    3 Results
  • Internal Controls
    3 Results
  • Body
    3 Results
  • Oven
    3 Results
  • Door
    3 Results
  • Wiring Information
    3 Results
  • Door (serial Prefix 11)
    3 Results
  • Body (serial Prefix 11)
    3 Results
Find part by diagram >

Question and Answers

Q:

Can I change this part myself.

A:

Having to work on replacing parts on the range can be rather difficult . While you are waiting for a detailed reply from an expert I would recommend visiting the Sears parts direct website were you can view a parts diagram to your model, which will allow you to get an idea of the task that needs to be performed. I have provided the link below.; Hope this helps!

Read More
Priscilla V -
November 14, 2012
A:

Thanks I went there first and I need some more info on the part number, but mostly I am wondering if I can even get to the part What I read there is just removing the old and putting on the new, but I'm not sure how to removed the cover that is over the clock and dials.

Read More
Trish -
November 14, 2012
A:

Thank you for your question and I understand your concern.

I added an image below with the procedure of removing the control panel. This will give you access to the electronic oven control/clock assembly. NOTE: Disconnect the range from the power source before servicing. The clock/oven control will be fastened with screws. Transfer one wire at a time from the old control to the new control. If the new clock/oven control comes with instructions, follow the instruction provided.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
November 15, 2012
See more answers
Q:

Clock display turns off

A:

ManageMyLfe.com is a great place to find your owner's manual and installation guides for appliances. I did some research and found the owner�s manual in where you can find some good information about your appliance. I have attached the link below. Your expert will follow up and verify this information shortly. If you are having a specific problem please submit your question on the existing thread by click on the reply box below for your expert.

Read More
Joseph P. -
November 05, 2011
A:

Thanks. I have the owner's manual, but it does not address the condition.

Read More
Anonymous -
November 05, 2011
A:

Thank you for your question and I understand your concern.

Based on your symptom and details it sounds like a there may be fluctuation in the power supply voltage. It sounds like the voltage supply will need to be checked during operation of the range. I recommend calling a service technician to check the power supply and diagnose the failure. If could just have a loose Neutral connection at the range, breaker box or at the utility pole causing a floating Neutral. NOTE: I do not recommend checking and monitoring the voltage supply unless you have experience and feel safe and confident in doing so; otherwise I highly recommend calling service technician to diagnose the problem.

You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
November 07, 2011
A:

There are some dark stains, which seem to indicate leakage from what i think is the transformer on the circuit board housing the relays. Could a faulty transformer cause the display to blank out? If so, will the display recover after replacing the relay board?

Read More
Rimas -
November 07, 2011
A:

Rimas: The transformer should not be leaking. Replacing the relay board will most likely resolve your problem providing it's not a voltage supply issue. The transformer on the relay board is what powers up the electronic oven control/clock assembly.

Read More
Joey S -
Sears Technician
November 08, 2011
A:

Thanks. I'll replace the relay board and hope the new clock panel was not fried by the condition of the transformer. You mention voltage supply: is that at the outlet or within the range circuit?

Read More
Rimas -
November 09, 2011
A:

Rimas: That would be the voltage supply to the range. Voltages can drop or spike during power outages, rolling black outs or during an electrical storm. Since you found the power transformer apparently leaking, replacing the relay board will most likely resolve the issue.

Read More
Joey S -
Sears Technician
November 09, 2011
A:

Thanks. I'll let you know how it works out.

Read More
Rimas -
November 10, 2011
A:

Replacing the relay board seems to have fixed the problem--clock panel still ON after a week. I wish I hadn't rushed into replacing the clock panel first: a $200 mistake.

Read More
Rimas -
November 19, 2011
See more answers