Model #62945765 KENMORE Slide-In Range, Electric

  • Top Assembly
    3 Results
  • Internal Controls
    3 Results
  • Body
    3 Results
  • Oven
    3 Results
  • Door
    3 Results
  • Wiring Information
    3 Results
  • Door (serial Prefix 11)
    3 Results
  • Body (serial Prefix 11)
    3 Results
Find part by diagram >

Question and Answers

Q:

Problems with my Kenmore Drop in Range oven

A:

I understand how it can be frustrating when it comes to the oven on your range not working properly. I have taken the time to research on the Manage My Life website and have located similar information towards you issue. While you are waiting for a detailed reply from an expert I have attached the links below. Hope this helps!

Read More
Priscilla V -
March 29, 2012
A:

Check to see if the broiler works properly. If that broiler heats up to the proper temperature and works, then you could have a problem with that bake element. I recommend that you shut off the house circuit breakers for the range and check that element. Here is a link for a video that shows how to remove that element: Bake Element Replacement . This video shows how to test that element using a volt/ohm meter: Bake and Broil Element Testing . That element should measure between 10 and 40 ohms of resistance (probably around 17 ohms). If that bake element is bad, it will need to be replaced. You can order that element from this page: Bake Element for Kenmore Range 629.45765 . Be sure that you shut off the house circuit breakers to completely disconnect electrical power before accessing and replacing that element. Do not leave the wires for that element exposed and power the range back up. The ends of those wires could short out against the metal cabinet and cause problems. Reconnect the wires to the element or leave the power disconnected until you complete that repair.

If that bake element is okay, you could have a wiring problem, a bad control board or a number of other failures that would prevent the oven from heating properly. I provided a wiring diagram with the bake and broil element circuits traced in colors below this response. You can shut off the house circuit breakers for the range and check that wiring. These initial tips may help you fix that oven heating problem. Reply with additional details if you need more assistance diagnosing and repairing this failure.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 30, 2012
See more answers
Q:

Kenmore drop-in range burner replacement

A:

That's great that you are wanting to change the part on the range. I was able to find the Owner's Manual for you its great to have handy. The expert would be able to answer your question specifically.

Read More
celene -
February 04, 2011
A:

I don't have pictures or written instructions for replacing a burner on this type of range. You can follow these general directions:

  • Shut off the house circuit breaker to disconnect electrical power.

  • Pull the range out from the counter.

  • You should find screws along the sides of the range that secure the main top to the frame of the range. Remove those screws.

  • Open the oven door. You may find screws under the front lip that also secure the main cook top. Remove any screws from this area if you find them.

  • You may then be able to carefully lift the cook top up. You may need to open the console and disconnect wires. You will need to rely on your personal observation of the range. You can view the parts list diagram on the Sears PartsDirect website. The parts diagram may help you access and replace the burner.

These general tips may help. If you do not feel confident replacing this burner yourself, then you can have it installed by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 07, 2011
See more answers

Top Parts