Model #6150 MANCO Gokarts/Minibikes

  • Cylinder Head
    3 Results
  • Cylinder
    3 Results
  • Engine Crankcase
    3 Results
  • Transmission
    3 Results
  • Cvt Cover
    3 Results
  • Outer Crankcase
    3 Results
  • Piston/crank/conncting Rod
    3 Results
  • Camshaft
    3 Results
  • Oil Pump
    3 Results
  • Driven Pulley/clutch
    3 Results
  • Engine Electrical
    3 Results
  • Electric Start
    3 Results
  • Driver Pulley
    3 Results
  • Oil Cooler (not Incl 6150 Model)
    3 Results
  • Fan Cover/shroud
    3 Results
  • Carburetor
    3 Results
  • Frame Group
    3 Results
  • Steering
    3 Results
  • Front Suspension
    3 Results
  • Rear Cargo Rack
    3 Results
  • Rear Swingarm
    3 Results
  • Engine
    3 Results
  • Rear Axle
    3 Results
  • Electrical
    3 Results
Find part by diagram >

Question and Answers

Q:

GE Washer not Spinning or Agitation WPRE6150k2WT

A:

Original Poster Re-post without special characters issues: Thank you for your generous advice. I have a GE Washer WPRE6150k2WT; Hydrowave green LED on Motor inverter board; no flap. The unit fills and drains but will not agitate or spin. The LED on the motor inverter board flashes 1 sec on and1 second off (no motor movement) so I assume the fuse is OK. The LID open LED display works as well as stopping the filling when the LID is open so I assume the LID switch works ( also from voltage readings below). I obtained a reading of 68 ohms across the mode shifter. There were not any error led indicators on the selector leds in the service mode Motor inverter board voltage measurements. C2 connector: 120 V pin 5 (RB) to ground. 120 V pin 6 (SX) with lid down ( 0v with Lid up) C4 Connector (same readings in mode selector �??drain/spin�?? and service mode SP) All pins 54 V. (Pins RX, YX, NX,BX, VX) Connector wired to motor windings Second from right (connector not on the schematic but two wires Lt Blue and Black to motor coils )

Read More
stuart -
August 17, 2015
A:

original poster Little more information The motor winding wires have 120v on both the Lt Blue and Black wires at inverter board connecter. This voltage is present whether or not the C4 control board to inverter is connected. Thank you

Read More
stuart -
August 17, 2015
See more answers
Q:

Loud spin cycle WPRE6150K1WT Ge Washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when you have a loud spin cycle.


WH2X1198 is the tub bearing that may be going out. I first recommend checking the pulley and belt to make sure those are not causing the noise.

 If the washer is making a loud noise the drive pulley might be worn out, cracked, loose or bent. Remove the drive pulley and inspect it carefully. If it is damaged or defective replace it.

You will need to disassemble your washer in order to inspect the parts. 

 To Remove Front Panel:
1. Locate two spring clips between cover 
and front panel, by aligning putty knife with 
groove on either side of lid and cover. 
2. Insert putty knife and push forward to release 
clips.
3. Rotate front panel forward and lift off cabinet base 
locating tabs.
4. Reverse procedure to reassemble.

To Remove Cover/Lid Assembly:
1. Remove front panel using step 3 .
2. Remove two 1/4" hex screws on front of cabinet.
3. Reach under the lid assembly and locate lid switch. Squeeze lid switch latch in to release while gently pushing it upward. Guide through lid switch opening.
4. Remove cover/lid assembly.
5. Reverse procedure to reassemble.

To Remove Spin Basket:

1. Follow steps 3 and 4 .
2. Remove five hex screws from control panel bracket. Tilt bracket up and out of the way. Note that the water valve and fill nozzle are attached to the control panel bracket as well. On some models, the load-size switch is attached to the control panel bracket. If this switch needs to be removed, tilt control panel bracket up and squeeze load-size switch mounting snap with pliers from underside to 
remove.
3. Disconnect four dampening straps from tub attached by 5/16" hex screws.
4. Remove tub cover by lifting out eight molded tabs on tub cover, and pull cover off.
5. Lift the dispenser top tab and turn the top counterclockwise using the 2 turning tabs. Lift the dispenser out of the pulsator.
6. Remove 7/16" hex bolt attaching pulsator to spline shaft.
7. Remove pulsator by lifting it straight up and off the shaft.
8. Remove left-handed 1-11/16" hub nut. This nut is aluminum; take care not to round the edges when 
removing or replacing.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the unit before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

Read More
Natasha12 -
Sears Technician
August 10, 2015
Q:

kart has no spark 6150 Manco Fun kart

A:

Thanks for the inquiry and for being a valued member.

The spark is generated by the magneto (part 14365), and the flywheel (part 14366). Check the magnets for any surface rust and lightly sand them if needed. I am not too familiar with this design of magneto, but you can usually pull the kill wire and check for spark with the wire disconnected. If you have spark, the kill wire would be the issue. If there is still no spark, it's typically magneto or magnet related.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
July 06, 2015