Model #6119 ZENITH Direct View\Digital 27" to 40" TV

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

How to fine tune 1986 sear radial arm saw Re: saw carriage bearings and tracks

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
February 17, 2012
A:

Thank you for your question on tuning up the radial arm saw. I will help you all I can.

Since you will need to remove the carriage from the arm I would put all new bearings on the carriage.

There are eccentric bolts for the rollers on the left side of the carriage that you can adjust to tighten the fit between the arm and the bearings.

This link may be helpful to you for tuning up your saw.

Tuning up a radial arm saw .

I also have put in a link for the owners manual for the saw and it will address the adjustment of the carriage rollers for tuning the saw. I am sorry that we do not have it available for download.

113.29950 Owners manual .

Please let me know how it goes and if I can help your more.

Sam A.

Read More
Sam A -
Sears Technician
February 18, 2012
A:

Dear Sam A. Thank you. I will follow your suggestion and buy and install 4 new bearings. The tracks on which these bearings ride seem to be 'true'. If not, then buy new tracks. After installation I know I must re-tune starting at #1 and going thru each step. I am sure currently I have 'heel'. I have a manual for this model: 113 199250 It is an older unit (1986) but it has not been abused or left to rust. It is apparant that since 1986 there are many newer tools that do a better job.....that's life. jfb

Read More
john -
February 18, 2012
See more answers
Q:

saw runs rough

A:

Table saws can develop problems like this that make using them difficult if not unsafe. While you wait for the expert response, I attached the link to the owner's manual just in case you did not have it. The expert will respond within 24-48 hours if not sooner.

Read More
Barbara H. -
February 11, 2012
A:

Thank you for your question on the old radial arm saw.

John I can see your e-mail without you having to put it in the web site. I have redacted it to remove it from the site.

It sounds like you have bent the blade and I would suggest that you replace it. You can check the arbor without the blade by putting a object very close to the arbor shaft and turning the saw on briefly and observe to see if the arbor shaft is bent.

I am sorry but the eccentric bolt is no longer available from our parts source.

I am afraid that the track rods may also be no longer available also.

The carriage bearings are still available and this may be all you need unless you can feel or see a divot in the track rail.

Carriage bearing .

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
February 13, 2012
See more answers
Q:

table saw runs rough

A:

This is John again, could you please reply to my e-mail at jmbecker817@verizon.net.

Read More
john -
February 11, 2012
A:

Table saws can develop problems like this that make using them difficult if not unsafe. While you wait for the expert response, I attached the link to the owner's manual just in case you did not have it. The expert will respond within 24-48 hours if not sooner.

Read More
Barbara H. -
February 11, 2012
A:

Thank you for your question on the old radial arm saw.

I am sorry but the eccentric bolt is no longer available from our parts source.

I am afraid that the track rods may also be no longer available also.

The carriage bearings are still available and this may be all you need unless you can feel or see a divot in the track rail.

Carriage bearing .

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
February 13, 2012
See more answers

Top Accessories