Model #60251 INFLATABLE BOAT Inflatable

  • Reapir Kit And Accessory
    3 Results
Find part by diagram >

Question and Answers

Q:

Malfunction Craftsman 12" Band Saw Model No. 113.24350 Lower wheel bound

A:

I can appreciate your description of the problem you're experiencing. With the wheel moving side to side it may well be a bearing issue. I've located a link that is similar to your model number. It does not address the bearing question (the expert that responds will do that). It does give detailed instruction on replacing the wheels themselves. I include it here because it provides very useful information I feel could be helpful should the need arise. Click on the link below to view the page. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
August 06, 2013
A:

Thanks for your help. I will check out the link you provided. I have been working on getting the wheel off without much success so far. Tried a little WD-40 but is not cooperating yet.

Read More
JD -
August 06, 2013
A:

I appreciated the link, however, it was referring to the replacementl of the rubber tire which goes on the wheel. No feedback yet - so proceeded and was able to remove lower wheel. I am assuming my problem lies with the bearing and, therefore, need to remove part nos. 4,11 & 27. (Retaining ring, ball bearing & spacer bearing) which is my next dilemma. Does anyone have any experience with this? Do I need to take it somewhere with a bearing puller? Or, is there a way I can do it? I believe the retaining ring disintegrated as there were remnants in front of the bearings.

Read More
JD -
August 06, 2013
A:

OK, Now after doing more research, I know the problem is definitely a bad bearing and that I need access to a bearing removal kit. Does anyone have any idea which kit would be suitable for the job and where I might find it?

Read More
JD -
August 06, 2013
A:

Thank you for your question.

 

I am sorry you are having a problem with the Craftsman band saw model 113.24350 . If the wheel is hitting the bottom of the table and you can move it back and forth, I suspect the problem is in the bearings. To check the bearings you need to first remove the wheel from the shaft. It is secured with a setscrew. Once the setscrew is loosened, you should be able to slide the wheel off the shaft. Be careful not to lose the shaft key. Once the wheel is removed, move the shaft up and down. If there is any play, the bearings need to be replaced. Before ordering the bearings, I recommend taking the shaft out and inspect it. If the shaft is not gouged up it should be ok to reuse it. The replacement parts for the band saw can be ordered from the following link. Replacement parts for a Craftsman band saw model 113.24350.  

 

Thank you for using Mange my life.

 

 

Mark T.

Read More
Mark T -
Sears Technician
August 07, 2013
A:

Thanks Mark. I have removed the wheel and am sure the problem are the bearings. My next question is locating the correct bearing puller kit. Can you recommend one?I assume that after removing the old bearing, the new one can be tapped on? I do have one other related question. Looking at the Owner's Manual diagram of parts- it shows two #11's (part no. 60251-ball bearings) on the chart-one on the left side of the saw and one on the right. Do I need to order two or is there actually only one which is being shown twice?

Read More
JD -
August 07, 2013
A:

JD, Once you have the snap rings removed, you should be able to slide the shaft out. If it will not come out you can try a soft face hammer. Then use a hammer and punch to knock the bearings out of the base. To reinstall the bearings, just place the bearings against the base and drive them in with a block of wood and hammer. This is usually how I replaced them. Please let me know if you need further assistance. Mark

Read More
Mark T -
Sears Technician
August 16, 2013
A:

Mark, I ordered and just received all of the replacment parts. I will try your method of tapping the bearings in place with a block of wood - thanks. I do have one problem, however, that I need help with. On p. 24 of the bandsaw manual is indicates a key #12 - Internal retaining ring - 1-11/16" as being between the pulley side bearing and key#5 - spring washer. I ordered this part and received a pair of rings. My problem is that the old bearing assembly that I removed does not have this part and I cannot understand how the ring would be held in place or is needed. The manual does not show the ring on the wheel side diagram, so I assume only one is needed? Can you explain? Thanks!

Read More
JD -
August 17, 2013
A:

Piece of cake (except just found that bearings to top wheel also need replacing). They come off much easier. For some reason bearings to bottom wheel about same size cost $17.00 ea while the bearings on top cost only $3.99 ea. Thanks for your help.

Read More
JD -
August 18, 2013
A:

JD, I am glad to hear you were able to replace the bearing without much trouble. Please let me know how the upper bearing replacement goes.

Read More
Mark T -
Sears Technician
August 23, 2013
See more answers
Q:

Band saw wheel shaft bearing removal

A:

Good morning... I can fully understand your interest in getting instructions for this kind of bearing repair. I did locate a link that will discuss this situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help you and have a nice day.

Read More
Henry -
February 28, 2013
A:

There should be a retaining ring that holds the bearings in place. In most instances, the bearings will need to be driven or pressed out once the retaining ring is removed.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
March 02, 2013
A:

Hello, I have the same problem and found you thru search after posting my question. My lower wheel was rubbing against the table and binding. I received information this is likely due to a bad bearing. I removed the wheel and am now trying to figure out how to remove the bearings. Could you please further elaborate on the procedures needed to drive or press out the bearings? Do I need to take the bandsaw to someone with special equipment that can do this? Thank you.

Read More
JD -
August 06, 2013
A:

Yes, you need to take your wheel to someone who has a hydraulic press to remove the bad, and press in the new bearing,

Read More
George -
August 06, 2013
A:

I removed the entire unit (Shaft with 2 bearings, spacer and retaining rings). I don't suppose there's anyway Craftsman would sell me the entire unit so that I don't have to take everything apart and put it back together. Probably will call the parts section and they will tell me to call the technicians who will tell me to send the unit in so they can repair it.

Read More
JD -
August 10, 2013
See more answers