Model #59676514500 KENMORE Bottom-Mount Refrigerator

  • Handles & Trim
    3 Results
  • Left Refrigerator Door
    3 Results
  • Right Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Ref Dr Storage & Center Hinges
    3 Results
  • Controls
    3 Results
  • Refrigerator Shelving
    3 Results
  • Interior Cabinet
    3 Results
  • Freezer Shelving
    3 Results
  • Evaporator Area & Rollers
    3 Results
  • Compressor
    3 Results
  • Cabinet Back
    3 Results
  • Ice Maker 61005508
    3 Results
  • Supplemental Information
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Ice cubes hollow 59676514500 Kenmore Kenmore refrigerator

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Anna T -
May 10, 2013
A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. First make sure the water filter has been changed over the past six months. If it has, most hollow ice cubes indicate that the water pressure is not high enough to properly fill the mold in the ice maker. Perform the following checks for water pressure problems:

  1. If you have a water dispenser, check for proper water flow. You should be able to dispense at least 3 ounces of water within 5 seconds from your dispenser.
  2. Check your water filter status if you have a water filter on your refrigerator. A used up filter can restrict water flow to your ice maker. Many filter systems have an automatic bypass. You may be able to pull the filter out and check for improved water flow.
  3. Check your water supply line for kinks. If you do not have a dispenser, you can shut off the water supply, disconnect the supply tube, and check the water flow directly from the supply tubing. Place the tube in a bucket and turn the water supply on to check the flow.
  4. Cycle your water supply cut off valve. This valve is usually behind the refrigerator depending on your particular installation. If your valve is a small self tapping saddle type valve, it is prone to clogging. This particular type of cut off valve is not recommended for refrigerator water supply lines.
  5. If you have a reverse osmosis water filter system installed on your water supply to the refrigerator, you will need to reconnect the tubing directly to the regular house water supply. A reverse osmosis system will not deliver the minimum 30 psi water pressure needed for most ice maker systems.

I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
May 11, 2013
See more answers
Q:

What should I do if my kenmore refrigerator and freezer are not cooling after leaving the doors ajar?

A:

If the refrigerator is not cooling, it is possible that the evaporator coils accumulated an excessive amount of frost on them during the period the door was open. Another possibility is that the compressor overheated and has shut itself off and refuses to start while it is still hot. The unit will correct itself but it may take some time. The defrost cycle will eventually remove the excessive frost if it is there.

You can turn the unit off and leave the freezer door open overnight. This should be enough to thaw the evaporator coils and cool the compressor if it is over heated.

Note : Don't radically change the temperature setting. Adjust the control only to the next higher or lower setting. Wait 24 hours to allow the temperature to stabilize. This is the most important step and cannot be rushed. If the temperature needs to be adjusted further, repeat the process. Make sure to leave all doors closed to speed up the cooling process.

If the refrigerator still isn't cooling I highly recommend having a technician come out to diagnose and repair your appliance.

Read More
Korinna S -
Sears Technician
February 04, 2010
Q:

Why do I have to raise the freezer door to close it?

A:

The door may need to be adjusted. There is a new bracket for some models to give it more adjustment. Order bracket door/slide kit Service Part Number 12002230. It's available at Sears PartsDirect . Your model is not listed but the bracket still might fit on your freezer door. If it won't fit, try leveling the cabinet with the front leveling legs, this solves a lot of door problems. If you need more assistance you can resubmit your question with more details.

Read More
Scott D -
Sears Technician
May 14, 2009

Top Parts