Model #59657059600 KENMORE Side-by-Side Refrigerator

  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Handles And Grille Sump
    3 Results
  • Fz Door And Facade
    3 Results
  • Hinges
    3 Results
  • Controls
    3 Results
  • Air Tunnel, Drain Funnel & Toe Grille
    3 Results
  • Refrig Shelves & Crispers
    3 Results
  • Fz Shelf
    3 Results
  • Evap Fan Assy, Lights & Water Filter
    3 Results
  • Evaporator Assy And Rollers
    3 Results
  • Lights And Ice Maker
    3 Results
  • Compressor
    3 Results
  • Cabinet Back
    3 Results
  • Ice Bucket Assy
    3 Results
  • Ice Maker
    3 Results
  • Supplemental Information
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I have this refrigerator in the garage and I set the temperature to 43 but it goes down to 32 and freezes the pop. What do I need to do? 59657059600 Kenmore Kenmore refrigerator

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

It sounds like something is wrong with the fridge. Not so much that it is where the fridge is but how long the fridge is running. The thing you’re going to want to check would be thermostat and diffuser. If the diffuser is stuck open then the air from the freezer is going into the fridge too much.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
Samantha A -
Sears Technician
November 22, 2014
Q:

Kenmore water in door not working 59657059600

A:

I understand that your Kenmore water in your refrigerator door is not working properly. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
January 26, 2013
A:

I don't see your links.

Read More
Marty -
January 26, 2013
A:

Marty, if the water valve and filter have been replaced and the pressure is still low, this could be a problem with the filter housing or low pressure to the unit. Disconnect the power from the unit and shut the water supply valve off. Now, disconnect the water supply line from the water valve. Place the end of the water line in a pitcher and turn the water supply valve back on. If the pressure is low, check for a kink in the water line or it may be a problem with the valve. If there is good pressure, the filter housing # 67006524 will probably need to be replaced. I hope this will help you.

Read More
Scott D -
Sears Technician
January 29, 2013
A:

Thanks, I will check out both. What can go wrong with the filter housing?

Read More
Marty -
January 28, 2013
A:

I removed the filter, which is new and replaced with the plastic cap. The water pressure was back to normal. What's wrong with the filter housing?

Read More
Marty -
January 28, 2013
A:

Marty, if the water pressure is good with the by-pass but is reduced when the filter is installed, it indicates the new filter is blocking the water flow. Exchange the filter and if the same problem still occurs, then the filter housing will need to be replaced.

Read More
Scott D -
Sears Technician
January 29, 2013
A:

The filter is new. I had the same pressure problem before I replaced the filter.

Read More
Marty -
January 29, 2013
A:

Marty, if the water pressure is ok with the filter bypass in place but low with both the original and new filter, it indicates that either the water pressure to the refrigerator is low or there is a restriction in the filter housing with the filter in place. A good check for the water pressure will be to measure the water coming into the unit. You should get approx. 9 ounces in 5 seconds. If the water pressure does check ok, then the filter housing will probably need to be replaced. I hope this will help you.

Read More
Scott D -
Sears Technician
January 30, 2013
See more answers

Top Parts