Model #59653469300 KENMORE Side-by-Side Refrigerator

  • Handles And Trim
    3 Results
  • Fz Door And Facade
    3 Results
  • Hinges
    3 Results
  • Ref/fz Door And Shelf
    3 Results
  • Fz Shelf
    3 Results
  • Crisper Assy
    3 Results
  • Deli And Ref Shelf
    3 Results
  • Lights And Ice Maker
    3 Results
  • Evap Fan Assy And Lights
    3 Results
  • Light Covers And Toe Grille
    3 Results
  • Controls
    3 Results
  • Ice Bucket Assy
    3 Results
  • Cabinet Back
    3 Results
  • Evaporator Assy And Rollers
    3 Results
  • Machine Compartment
    3 Results
  • Supplemental Information
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

slab ice in ice maker tray 59653469300 Kenmore Kenmore refrigerator

A:

Thank you for your inquiry on your Ge Washer, Model: WSSH300G0WW. From reviewing the details on your model, I have provided a link to a couple of videos on similar model of refrigerators, which should be able to troubleshoot what could be causing the ice maker to slab up. The link I found below.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the refrigerator to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 10, 2015
Q:

Air flow to fridge low, what might be the cause? Kenmore Kenmore refrigerator

A:

Thank you for contacting SearsPartsDirect.com with your question about your Kenmore refrigerator. I am so sorry to hear that the air flow to the fresh food section is low. I know how inconvenient it is when the refrigerator isn’t working properly. I will be happy to help you with this.

 

Based on the symptoms you described, I recommend you check the damper control. When the thermostat in the fresh food section detects that the temperature has risen to a preset level, it signals the damper to open and allow cold air in from the freezer section. The damper stays open until the thermistor senses that the temperature in the fresh food section has dropped to a certain level. Then the damper closes.  If the air flow is low, it sounds like the damper is either blocked or stuck in a partially open position.

 

Unfortunately the model number you provided, 596.53569300 doesn’t appear to be a valid model number. Please re-verify the number from the inside of your refrigerator and respond to this thread and I will be happy to research this issue for you further, if needed.

 

I hope this answers your questions. If I can be of further assistance please respond to this thread. Thank you for choosing Sears, we appreciate your business.

Read More
Rachel Morgan -
Sears Technician
October 30, 2013
A:

Thank you for your answer from before. Correction refrig model 59653469300. Pull apart several areas of the frig. Check continuity on compressor, and capacitor control unit they were fine. Check the continuity of wiring harness to ADB every was fine. Did not know how to check board or the cold control unit. After re-assemblying fridge things were fine for a week. The other day woke up to water on floor. No frost on evap coils. Condenser coils were cool to touch. I still hear compressor and both fans going. I don't know what the problem is. Search the net for solutions some threads indicate that there is a sealed system problem. Is there a way to check the other items to rule out the thermostat/h part near the evap coils or the ADB board or the freezder control unit or damper control unit. Would there be any other reason for cool condenser coils besides sealed refrigeration system? Additional info: cold air is coming out of the back panel and also from the front toe grille.

Read More
Verynice -
November 03, 2013
See more answers
Q:

What is causing the dispenser agitator bar to keep coming loose from the helix cap?

A:

It could be due to the cap not fitting good on the driver. This is the part that connects to the auger motor and turns the helix. It could be a problem with the helix or the agitator bar. There have been no problems with this. If there is nothing you can see that is loose or not connecting good, I recommend replacing the complete assembly # 12740302 or having a technician check this. This assembly is available at Sears PartsDirect .

Read More
Scott D -
Sears Technician
August 12, 2009

Top Parts