Model #58717259200 KENMORE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame & Wrapper
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Manual for Kenmore Dishwasher - D22 M17259

A:

When looking for the owners on an appliance, Manage My Life is here to help. While you are waiting for your expert answer, I suggest you add to the the thread of this question and include the full model number of your appliance that the expert can provide you with a more detailed answer. I am adding a link in where you can enter your appliance model number and the owners manual will pop up. I hope my link is useful.

Read More
Joseph P. -
August 10, 2011
A:

Hi Joanie,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

The model number you gave me is inaccurate or incomplete. I will assume you have one of the following 587.17259200, 587.17259201, or 587.17259202.

Here is a tech sheet for this type of dishwasher. If you would like specific help with your dishwasher, please reply to this post with the correct model number and more details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
August 11, 2011
A:

Kenmore 18�?? portable dishwasher model # 587.17259201. Replacing door spring part # 15423740 This unit NOT built in, unit has side panels �?? need to know how to access door hinge assemble located on right side of unit, need to remove side panel �?? cannot find diagram or information on how to do this. How can I access instructions on this??

Read More
Karl S -
December 31, 2015
See more answers
Q:

dishwasher is dry

A:

I hate doing dishes by hand. I'm sorry to hear that you are having some difficulties with your Kenmore Dishwasher. I did some research for you at Managemylife and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope these links provided assist you.

Read More
James -
January 27, 2012
A:

Make sure that the water supply cut-off valve is fully open and that you have a proper water supply provided to the dishwasher. If you are using this dishwasher in a portable mode, then I recommend that you make sure that the faucet adapter is attached properly. You could have a problem with that adapter that is preventing the dishwasher from getting water.

You can unplug the dishwasher or shut off the house circuit breaker for that appliance and check the continuity through that float switch using a volt/ohm meter. Here is a link for a repair video that shows how to access the water inlet valve: Dishwasher Water Inlet Valve Replacement . The float switch is located close to that water valve. It is circled in red on that 2nd image below. Here is a video that shows how to check for continuity through that component: Multi-meter Continuity Test . If that float switch is bad, it will need to be replaced. You can order parts from the Sears PartsDirect website. If that float switch is okay, you can check the water inlet valve for continuity. If that water inlet valve is "open" then it will need to be replaced.

These tips may help you fix this water fill problem. If you need more help, reply with additional details.

If you get to a point where you need to have a service technician examine and repair the dishwasher, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 30, 2012
See more answers
Q:

Small leak under my portable Kenmore 587.17259200 dishwasher

A:

Check rubber seals around cabinet and knife edge on door for food or foreign mater can cause leaks. If found clean with wet towel or rag. Even small stuff can cause leaks. Also check if seal is missing or cracked is level or even all the way around to insure there is contact with knife edge.

Read More
thomashunt -
April 08, 2011
A:

Thank you for your question.

I am sorry you are having a problem with the dishwasher. I can be difficult to pin point a leak on a dishwasher. I have checked the model number you have submitted and we do not have any known issues with this model. I recommend removing the front access panel. This is the panel below the door that is secured with a few screws. Once the panel is removed, connect the dishwasher and start a cycle. Then use a flashlight to watch for leaks. Just make sure to keep your hands out while the dishwasher is plugged in. once you spot the leak unplug the dishwasher to inspect the area closer. If you need help with repairing the leaking component, please reply below with the details of what you found.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
April 09, 2011
A:

Thanks guys! This is great advice written really well! So far, I've cleaned the knife edge and gasket, which had some detergent scum build up, and this afternoon I'll run the machine with the access panel removed and a flashlight in hand.I'll let you know what happens. =) Mimi

Read More
mimi -
April 10, 2011
A:

Well, cleaning the knife-edge of the door and the cabinet-gasket did it! Before I knew that, I tried to takeoff the front access panel, so I could test everything together, but it was pretty tough to remove. I got the two screws on top, shown in the manual, but then there were two more underneath, and there I was propping the machine up on old books and juggling screw drivers which were too long or too short, and not having good leverage at that angle. So I ran it without removing the panel, and was delighted the leak was gone. Thanks again, -Mimi

Read More
mimi -
April 14, 2011
A:

I am glad you have cured the water leak. Please keep us in mind next time you have a problem.

Read More
Mark T -
Sears Technician
April 15, 2011
A:

How would you get those bottom screws off the front access panel? Or did I miss something, and would it have come off with a sliding maneuver of some kind?

Read More
mimi -
April 15, 2011
A:

Thank you for the reply. The screws have to be removed to take the access panel off. I know it can be difficult to remove theses screws. If it is a hex head screw, you can use a wrench to remove them. I am sorry there just not an easy way to remove them.

Read More
Mark T -
Sears Technician
April 16, 2011
See more answers

Top Parts