Model #58716074201 KENMORE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Dishwasher latch doesnt appear to be the same latch as the original.

A:

It is disappointing when you have received a replacement part for your dishwasher and it doesn't seem to fit. I researched your question and was unable to find any information that would be helpful. An expert will respond shortly. It usually takes 24-48 hours to receive an answer. Have a good day.

Read More
Jackie S -
May 18, 2012
A:

The 15437304 number is correct but I'm not so sure about the letter B at the end. The image below shows a picture of the 15437304 latch assembly. This part should work in your 587.16074201 dishwasher. Check the image below and see if it's similar to what you received.

Read More
Fred M -
Sears Technician
May 19, 2012
See more answers
Q:

the cover latch on my kenmore dishwasher (model 587-16074201) doesn't keep the main wash cup closed. it always pops open.

A:

I can see how having the detergent cup not stay closed to dispense properly would cause problems getting the dishes clean.. I normally check the owner's manual for help if I do not see anything that is obviously broken. I attached the link for your model below. It may help whie you wait for the expert answer. if you decide you would prefer to have a technician diagnose and make repairs,an option is to visit Sears Home Sevices and use the scheduler. I attached both links below, just copy and paste the links. http://www.managemylife.com/mmh/owner_manuals/10204/KENMORE-Dishwasher-L0206134?brand_name_search=587-16074201 http://www.searshomeservices.com/

Read More
Barbara H. -
October 24, 2010
A:

I've looked through the manual and was unable to find a solution. Thank you.

Read More
Anonymous -
October 24, 2010
A:

I can understand your concern with your dispenser door not staying latched. Based on your symptom, the dispenser assembly will have to be removed and replaced. The dispenser assembly is part #154574401 and is available to order and have it shipped to you from Sears Parts Direct .

I added an image below with the removal instructions.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
October 26, 2010
See more answers
Q:

Our Kenmore dishwasher, 587.16074201, doesn't start when the touch pad, "Start/Cancel" is touched. However, it will start in the delay mode.

A:

Having a Dish Washer in a home is so helpful when having to do a lot of dishes. A suggestion I have while you are waiting on an expert to answer your question. I found this really great link on Dish Washer. I attached the link below. Hope this helps! Good luck.

Read More
Dezeray S -
October 11, 2010
A:

Sorry to hear about your dishwasher not operating normally, but based on your details you have a very unusual and uncommon symptom. If the Start/Cancel pad works in order to Cancel the Delay Hours cycle after it has started a cycle then it should also work to Start the cycle after a cycle has been selected. I must assume you have tried each one of the cycles and then pressed Start and the dishwasher will not start but if you select any one of the cycles and Delay Hours and it will start, then I must assume the control board is faulty and not the key pad but I can't be 100% certain.

With this type of symptom I recommend calling a Sears technician to diagnose and repair your dishwasher. I recommend calling Sears at 1-800-4MY-HOME or 1-800-469-4663 to set up a service appointment.

Read More
Joey S -
Sears Technician
October 12, 2010
See more answers

Top Parts