Model #58715254402 KENMORE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

replace bottom door gasket 58715254402 Kenmore Dishwasher

A:

Thank you for choosing Sears, I will be more than happy to assist you with your Kenmore dishwasher.

Based of the information provided, I located step by step instructions on how to replace the bottom door gasket for the unit. If you click here you can access the steps.

I hope you found this information helpful. Thank you for choosing Sears Parts Direct. We appreciate your business. Have a great day.

Read More
Samantha A -
Sears Technician
November 06, 2014
Q:

My Kenmore dishwasher will run through the first wash cycle but will not progress to the 2nd or 3rd cycles of the wash. It fills and drains but then stops.

A:

I'm sorry to hear that you are having some difficulties with your Kenmore Dishwasher. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
James -
October 21, 2011
A:

Thank you for your question and I understand your concern.

If the wash motor will operate in the first wash but not operate in the 2 and 3 wash cycles could indicate a faulty wash motor or control board. The wash motor could be shutting off be the thermal overload protector inside the motor.

The only way to know which is faulty will require monitoring the voltage supply at the wash motor across the White and Blue wires connected to the wash motor. These wires can also be accessed at the control board as well for testing the voltage supply to the wash motor. NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dishwasher.

I added a couple of images below; one of the wiring diagram and the other is a test cycle. I recommend running the test cycle to see if the wash/circulation motor runs in steps 3, 5 and 6.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
October 22, 2011
A:

My dishwasher will go through all the cycles and the clean light will illuminate at the end but there will still be standing water in the bottom. If I hit Cancel and Drain, the dishwasher will empty. I've removed and cleaned all debris from under the screen and ensured that nothing was clogging the drain area. Any recommendations?

Read More
Rick -
April 22, 2012
A:

Rick: When the dishwasher drains after the first wash and first rinse, does it drain all the water? Does the drain pump operate in the last drain cycle before it reaches the dry cycle? Also, having the model number of your dishwasher would be helpful too. One more question; how much water is standing after the dry cycle?

Read More
Joey S -
Sears Technician
April 23, 2012
See more answers
Q:

Why does my Kenmore dishwasher not circulate water?

A:

The circulation of water in your dishwasher is dependent on just a few things.

The motor must run. This unit has a separate drain motor and when you push the cancel button it should drain and you will hear the drain pump.

When it circulates you should hear a motor sound. If the dishwasher fills with water then the door switches and voltage should be okay.

If you hear a motor sound and it is not circulating the water then there can be something in the sump blocking the circulation impeller on the motor.

Check the images below for assistance in checking for debris. The first is a picture of the area where the blockage can be and the 2nd picture are the instructions to access this area and check for debris.

Read More
Fred M -
Sears Technician

Top Parts