Model #58715252400 KENMORE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Ken more Dishwasher 587.15252400

A:

Good morning.... I found a link that is very similar in nature to your situation. The technician gives practical advise that I hope will be helpful to you too. Keep in mind that an expert will review your question and get back to you within two business days if not sooner. Until you hear from us again, have a nice day.

Read More
Henry -
October 25, 2012
A:

The seals are part of the element assembly and are not available separately I'm sorry to say. The silicone might work but is is not a recommended repair and I can't suggest you try it. The tub is an available item but it will cost approximately $175 dollars. If you try the silicone then I suggest you try it on the bottom side of the tub.

Read More
Fred M -
Sears Technician
October 25, 2012
A:

Check that the heating element mounting nuts haven't split

Read More
Chat in RI -
October 25, 2012
A:

Chat is correct. If the nuts are split then the unit may leak.

Read More
Fred M -
Sears Technician
October 28, 2012
See more answers
Q:

My dishwasher has stopped drying.

A:

Did anything melt on the heating coil? And you're sure that the odor is plastic and not electrical? I have located a link that will give you a path of travel that may give some insight. Review this data and your question will be forwarded to an expert who will review the matter further. I hope this link is helpful to you and enjoy your Sunday morning.

Read More
Henry -
September 30, 2012
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating it is having trouble with your dishwasher not drying the dishes. We are here to help. I suspect some wire burned on the dishwasher causing the smell. Since you already check the control panel and found nothing wrong, I recommend you check the wires to the heating element. If the wires are bad, I recommend you replace them and the heater thermastat. Most likely the thermastat was not turning off the voltage to the heating element. Therefore, the heating element was getting too hot and drawing too much current, causing the wires to melt. Also, I recommend the heating element be check out with a multimeter. A good heating element should read between 10-35 ohms. If it is not within that range, replace the heating element. I hope this helps.

To order dishwasher parts, please visit SearsPartsDirect.com with the model number.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
October 01, 2012
See more answers
Q:

what is the dB level of dishwasher model #: 587.15252400?

A:

Needing to know the DB level on Dishwasher is a very great question to know. I researched your question and I found this great link on different model numbers with DB levels.I attached the link below. Hope this helps!

Read More
Dezeray S -
November 15, 2010
A:

I am looking for the actual number for the dishwasher. It was purchased in 2006 and I can't find specifications on it anywhere. I have also talked to repair and the rep. there didn't have anything.

Read More
fge2003 -
November 15, 2010
A:

Some dishwashers were not rated for noise level in 2006. I don't find a rating on that model of dishwasher. Based on similar models that use the same motor, it will likely produce about 55 dB of noise.

Read More
Lyle W -
Sears Technician
November 17, 2010
See more answers

Top Parts