Model #58715242702 KENMORE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore dishwasher won't shut off 587.15242702

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dishwasher is not working.

 
 For a brief test, you can tape the ends of the wires that go to that thermostat together using electrical tape. This will bypass that high limit thermostat. See if the element will heat and the cycle will work properly with that thermostat bypassed. If it does, then the fuse will need to be replaced. 
Most likely you need to replace the control board 

154712101 is the board.

 You can also visit searpartsdirect.com for parts, diagrams, and repair information.

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 29, 2015
Q:

Does not spray water 58715242702 Kenmore Dishwasher

A:

Thank you for choosing sears I would happy to help you with your dishwasher. Upon researching model 58715242702; it sounds like either the float switch or the inlet water valve may need to be replaced. The overfill float switch is located under the tub and is attached to the mushroom float inside the tub, which raises and lowers with the water level in the tub. When the overfill float switch detects that the water level is too high, it shuts off power to the water inlet valve, stopping the flow of water into the tub. Even if the mushroom float is working properly, the micro-switch could have failed. The water inlet valve, also called a solenoid fill valve, controls the flow of water into the dishwasher by opening and closing. If the water inlet valve doesn't open at all, water can't flow into the dishwasher. If it opens partially, the dishwasher won’t fill adequately, and the water level will be low—a noisy pump is one indication that the water level is low. Conversely, if the water inlet valve won’t close, water fills the dishwasher tub even when the dishwasher is off. If the water inlet valve doesn't open or close correctly, repair or replace it.

 

I trust that this information will help you, thank you have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
October 21, 2014
Q:

Dishwasher 58715242702 Kenmore Dishwasher

A:

Thank You for choosing Sears PartsDirect.com. Glad to help out. Im looking at your model number 58715242702  and this unit does have a delayed start feature. It is possible that the option is on. The DELAY START option allows you to automatically delay starting your dishwasher from 2-4 or 2-4-6 hours depending on the model. On models with 2-4-6 hour delay, press the pad once for a 2 hour delay, twice for 4 hours and three times for 6 hours. A light will come on indicating the delay start hours and will remain on unitl cycle starts. To cancel the DELAY START option and begin the cycle before the delay period is over, press the START/CANCEL pad. To cancel a cycle anytime during the cycle by pressing START/CANCEL pad and the dishwasher will start a 90 second drain. At the end of the drain, select the desired cycle.  If you have further questions please resubmit your question for further information.
 
Thanks for choosing Sears PartsDirect.com.
 

Read More
Sherman_G_Wallace -
Sears Technician
March 27, 2014

Top Parts