Model #58715182400 KENMORE Dishwasher

  • Control Panel
    3 Results
  • Door
    3 Results
  • Tub
    3 Results
  • Motor & Pump
    3 Results
  • Frame
    3 Results
  • Racks
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

24 " Dishwasher not working. It's plugged in. Checked all of the connections-wire to transformer, transformer to motor. It is a Kenmore Quietguard Standard.

A:

Dishwashers are great time savers. The problem with the dishwasher is concerning. I found some information for you that I am hoping will help you. Please click here:[Kenmore Dishwasher].Your expert will also help answer your question. It may take two business days for your expert to reply. I do hope that everything works out on the Kenmore dishwasher.

Read More
Marc -
August 06, 2013
A:

Thank you for your question and I understand your concern.

You did not make it clear where the constant clicking noise appeared to emitting from. Was it coming from the control panel or from underneath the dishwasher? You also did not indicate if any of the LED's is lit up on the control panel or not.

If there are no LED's lit up, the incoming voltage supply should be disconnected and measured with a voltage meter. NOTE: Flip the house circuit breaker OFF before removing the lower toe panel and the electrical junction box cover. Remove the wire nuts connecting the two black wires and the two white wires. The voltage is measured across the black and white wires supplying the voltage. If 110-120 volts is measured, the next step is to reconnect the power supply to the dishwasher and then access the control board and measure the voltage supply across the white wire connected to P2-9 and black wire connected to P2-3 and then across the white wire (P2-9) and the black wire with the white stripe connected to P2-2. Note: The door switches will need to be closed when making the voltage measurements across P2-3 and P2-9.

I added an image below of the wiring diagram with troubleshooting steps. NOTE: I do not recommend making any voltage checks unless you have experience and feel safe and confident in doing so; otherwise I suggest calling a service technician to diagnose and repair your dishwasher.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:Sears Home Services.

Read More
Joey S -
Sears Technician
August 07, 2013
See more answers
Q:

i need to replace a wire on the drying element in my dishwasher. can i do that without replacing the whole wiring harness

A:

I can understand how concerning this may be for you, I was able to research some information that can help you. I have attached the links below hope it helps!

Read More
Maira -
January 03, 2011
A:

I included a wiring diagram in the image below so we're both on the same page.

You say the wire went to resistor but the only thing in line with the element is the hi-limit thermostat.

The wire harness is available but for $50 dollars I understand your question. Can I use $1 dollar worth of wire to fix this problem instead of a $50 dollar harness?

I'd say yes you can.

You can't use just any wire however and wire nuts and electrical tape will be needed.

Take a sample of the wire to an electrical supply store or a "Used Appliance" store in your area and get some similar wire. The color doesn't matter but the size and gauge of wire does. The wrong type of wire might be a fire hazard.

Match the wire up and install with wire nuts and electrical tape and you should be okay.

Give me a reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
January 06, 2011
See more answers
Q:

Why won't the door on the soap dispenser open during the wash cycle on my dishwasher?

A:

Failure of the detergent dispenser door to open could be caused by several different problems. The springs on the door could be broken, you could have a failed latch mechanism on the dispenser, a wiring failure or a failed control board could be preventing voltage from reaching the actuator assembly or you could have a failed actuator. First, check to see if the dispenser door snaps open if the latch is manually activated. If not, then the dispenser assembly would need to be replaced to fix this problem. I recommend calling a service technician to repair this type of problem.

If the spring is good, look for a build up of detergent around the latch that could be interfering with it. Clean this area if necessary.

Accessing the control board and actuator assembly requires the front panel of the dishwasher to be removed after shutting off the breaker to disconnect electrical power. I recommend that a technician conduct this type of procedure.

If you want to avoid the service call and repair of this problem, you can add the detergent directly to the bottom of the dishwasher tub before beginning your wash cycle. The dishwasher should clean properly even when detergent is added using this method.

If you want to diagnose and repair this failure yourself (and you have the technical skills to safely access the internal components), resubmit your question with additional details and we will provide advanced technical help for fixing this problem.

Read More
Lyle W -
Sears Technician

Top Parts