Model #580767301 CRAFTSMAN Power Washer, Gas

  • Power Washer
    3 Results
  • Pump
    3 Results
Find part by diagram >

Question and Answers

Q:

How to change fuel tank on pressure washer model 580767301

A:

I understand that you want to change the fuel tank on your pressure washer. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful. Have a nice day.

Read More
Alina F. -
September 23, 2011
A:

Thank you for your request for the removal and installation of the fuel tank.

There are two versions shown for this fuel tank in the engine parts break down.

The serial number of the engine dictates which fuel tank this engine uses.

Used after date code: 99070400, part number 694260. Used before date code: 9907500, part number 694263.

Before starting remove any fuel from the old fuel tank.

There are 4 bolt headed screws that hold the tank to the tank frame that attaches to the engine.

Once removed locate the fuel line and remove it from the valve on the bottom of the fuel tank.

There are a number of fuel line configurations and if you look at the parts view you can match up the correct fuel line and it should attach to the fuel tank shut off valve and attach to the inlet of the carburetor.

Fuel tank part picture .

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
September 26, 2011
See more answers
Q:

i have a craftsman pressure washer, model 580.767301 i need to order kit 0

A:

Getting the right parts is so important and getting help with repair is a plus. The Sears Parts Direct link below should be able to help you get the kit needed and the expert after review can provide the instructions. If you need the owner's manual for more information and diagrams I attached below also. Hope this helps.

Read More
Barbara H. -
June 24, 2011
A:

Thank you for your question.

If I have understood you correctly, you cannot remove the plug for the unloader. What happens is the water in the pump will start to corrode the manifold and the plug and making it difficult to remove. The easiest way I have found to remove the plug is with a six-point socket or wrench and hammer. If you use a six-point socket or wrench, it will not round off the head as easily as others will. Once you have the socket or wrench on the plug tap on the end of the wrench with the hammer. The sock from the hammer should break the plug loose. If it does not come loose you can try spraying it down with WD-40 and letting it sit for a few hours and trying it again. I hope this is helpful.

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
June 25, 2011
See more answers
Q:

Pressure Washer Problem

A:

Having issues with your pressure washer can be frustrating. While you are waiting for an expert to reply I recommend to reply back to this thread with a detailed question as to what issues you are actually having with your appliance. Which this will allow an expert to reply with a detailed answer.

Read More
Priscilla V -
March 16, 2011
A:

I am suspecting that it may have gotten damaged when I momentarily ran it with the water source shut off. It still somewhat works but the pressure coming out is not even close to what it used to be.

Read More
Joey -
March 16, 2011
A:

I'm sure it is repairable as in most cases they can be fixed. I do recommend you have a professional take a look at it to make sure though. But the parts for the pump are still available. The only time it gets tricky is if the whole pump has to be replaced, then it is usually cheaper to buy a new pressure washer.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
March 17, 2011
See more answers

Top Parts

Top Accessories