Model #58032782 CRAFTSMAN Generator

  • Control Panel
    3 Results
  • Cradle And Stator Assembly
    3 Results
  • Flywheel Assembly
    3 Results
  • Crankcase Assembly
    3 Results
  • Wheel Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

schematic

A:

I understand a schematic for the Craftsman generator is important to you and I was not able to find that information for you, however, an expert will respond with the information you are requesting within two business days. If you have an issue with the generator, just click on reply with the details. Thanks for your patience.

Read More
Anna T -
January 30, 2013
A:

Thank you for your question. I will be happy to assist you. I searched for the manual for your model but did not have any luck. I was able to find a manual for a Generac model that should be the same. Click here to load the manual. Towards the back of the manual is a diagram and schematic. I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 31, 2013
A:

there is about 6 volts ac at the 120 recptical. other post have suggested that the problem is the regulator. I am not sure that the regulator module is the problem. Any way to check it?

Read More
Jim -
February 04, 2013
A:

STILL LOOKING FOR ANSWER TO QUESTION

Read More
Jim -
February 08, 2013
See more answers
Q:

Craftsman 7500 Generator is not supplying Full voltage to the generator plugin panel for all the outlets provided.

A:

When the backup power supply can't carry the load needed, it is upsetting. The expert will review this model and respond within two days if not sooner. In the meantime, I did locate a similar question with a tip that may help. I attached to the first link below. I also added the link to this model at Sears Parts Direct if the diagrams or parts are needed. I hope this helps up that voltage.

Read More
Barbara -
July 26, 2012
A:

thank you! Im stressed!

Read More
Shad -
July 26, 2012
A:

Since there is some voltage there, I don't believe that "flashing the field" (as suggested in the link from Barbara) will change anything with your machine.

It sounds like the problem is very likely with the voltage regulator on the generator. If you have a meter, you can check to see if there is voltage coming into the regulator or not. I feel like there is a very good possibility of the regulator being the problem since most other stuff that can fail will fail in such a way where there will be no voltage at all.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
July 27, 2012
A:

Thanks, Wade I took my Volt Meter and Put it to "V" setting and set it at 600. I used the probes and touched both positive and neg sides of the brush sets while the brushes are still connected and mounted by the bearing and shaft that spins and where the copper rubs on the brushes (if that makes sense). It read 25 I then went to wires #2 and #6 on the Power Regulator board and touched those 2 with the Meter probes. It read 144. These 2 wires run to the STATOR Now, there is wires #1 and #4 hanging off the Power Regulator (that I unlugged from the brushes. I figured, well.....seeing how I have these 2 wires unplugged for the moment form the brushes, let me see if power is coming through those. So the meter gave me a reading of 305

Read More
Shad -
July 30, 2012
A:

I believe the voltage regulator has failed.

Read More
Wade_B -
Sears Technician
July 30, 2012
See more answers
Q:

generator valve adjustments

A:

Information for engine valve specifications is something the expert here at manage My Life can help with and you should have an answer within 24-48 hours if not sooner. if you decide you would prefer to take the system in for adjustment i attached the link to sears Home Services if needed.

Read More
Barbara H. -
February 23, 2012
A:

Check on the engine and see if you can find any kind of a model number for it. The model number for the generator does not bring up enough engine information for me to find the information you need.



I believe the valves will either be .004 on intake and exhaust or possibly .003 on intake and .006 on exhaust, but I can't find out for sure. If you cannot locate any kind of a model number on the engine, you may check in the owner's manual (if you still have it) to see if they list the engine model number there.



Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
February 24, 2012
A:

the engine model no. is a problem can not locate it and do not have the owners manual. which would be the safer settings to go with not having anyother information?

Read More
raymond -
February 24, 2012
A:

Set them at .004 and try it. If the setting is wrong, nothing bad is really likely to happen. The engine may not start and it's possible that the engine could backfire and snatch the starter cord back out of your hand so you may want to wear some leather gloves when trying it.

Read More
XX Wade_ -
Sears Technician
February 27, 2012
See more answers