Model #536888600 CRAFTSMAN Snowthrower, Gas

  • Engine Assembly
    3 Results
  • Electric Start Assembly
    3 Results
  • Frame Assembly
    3 Results
  • Drive Assembly
    3 Results
  • Gear Case Assembly
    3 Results
  • Discharge Chute Assembly
    3 Results
  • Auger Housing Assembly
    3 Results
  • Track Assembly
    3 Results
  • Handle Assembly
    3 Results
  • Handle Assembly
    3 Results
  • Headlight Assembly
    3 Results
  • Decals
    3 Results
  • Remote Chute Assembly
    3 Results
  • Chute Control Rod Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

i have a craftsman 536.85000 track drive snowthrower i would like to convert to wheels. is there a conversion kit availible?

A:

Definitely having to find the proper attachments for your appliance can be a challenge to help in determining if you have the right part I would suggest visiting Sears parts direct.com where you can view a diagram of all parts available for your SnowThrower, I have attached a link below. Hope it helps!

Read More
Priscilla V -
November 06, 2011
A:

I am sorry to tell you, there is no kit to convert the track drive on your snow thrower to wheels. The axle that drives the track will not fit a wheel. You would have to replace the axle and the drive unit and the cost would be prohibitive.

The model number you sent does not run in out system so I could not look at a parts diagram of the snow thrower. We have never had a kit to convert the track drive to wheels.

I looked at a model 536.88500 for reference.

Read More
Jimmy K -
Sears Technician
November 07, 2011
A:

Per the original poster request, I'm currious if one of your tracks is in need of replacements. Which in this case, the tracks may be obsolete as is the same case with my Craftsman 536.888600 snowblower. These snowblower series were manufactured by Murray & pretty decent machines. So, Sears nor Murray nor there vendor offers no replacement tracks at this time. In this case a wheel conversion kit would be necessary. The cost would not be to prohibitive as compared to purchasing a new & similar snowblower. Hub adapters should be available for the axle on these units. Sleeves may need to be used but will work fine. The trick is finding the correct wheel diameter so the speed selection will not be to fast or to slow for the gear box. Lot's of new conversion parts available on the internet. Once the pieces are put together, all should be well. Since SEARS provides no relief (other than sorry, which is unacceptable) to customers owning these older & expensive Murray units in need of replacement tracks (which are obsolete), the best source would be this company in China which offers a good track replacement deal for the money (http://www.tradevv.com/chinasuppliers/lhwfxj_p_17368d/china-Snow-Removal.html). I wish you well as the snow is coming soon :). Hope is out there.

Read More
Anonymous -
November 13, 2011
A:

Hi. I'm sorry to hijack the original post, but I would like to ask Mr. Anonymous if he'd like to sell parts from his 536.888600. Mine has a broken drive "wheel", part number 7089MA, which is of course discontinued.

Read More
Kevin -
November 16, 2011
See more answers
Q:

Can you help me find a manual for a Sears snow blower, model 536.888600?

A:

This particular manual has been permanently discontinued by the manufacturer and we don't know of any source to find it. I did however include a manual for a very similar model number. They should be very close. Please click on the following link. owner's manual

Read More
Landell -
Sears Technician
November 24, 2009
Q:

How do I adjust the auger belt, which seems to big, on my model 536.888600 snow blower?

A:

The image below shows the instructions to adjusting the auger belt.

The following link for the owner's manual for a similar model snow blower contains other information that may be helpful: Owner's Manual .

Read More
Fred M -
Sears Technician
March 19, 2009

Recommended maintenance parts & accessories