Model #5351 MILWAUKEE Drill Hammer

  • Drill
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a 139.5351SR garage door opner. I can hear the motor running but the cogs and gear are not moving. I replaced all the cogs about 3 year ago. 13953515SR Craftsman Garage door opener

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your garage door opener. Upon researching model 13953515SR; it sounds like you may need to replace the worm gear kit. The worm gears wears out over time and the teeth on the gear get stripped and no longer open the door. I have posted a link of the gear kit, to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
May 19, 2015
A:

I have this same unit. It appears something electrical in it just died while the garage door was being lowered, as it just stopped and will now not do anything. I've unplugged it and let it sit for over a minute. Plugged it back in. Still nothing. I then connected to a different known good power source, still nothing. Is there a reset button on it or a manual available? (Haven't removed the covers yet).

Read More
Darren -
December 05, 2015
See more answers
Q:

Compressor model # 919.15658 blows circuit breaker more and more quickly. Besides a motor going bad can anything else cause this? Any replacement motors work?

A:

here is a picture of the motor, which is a Doerr lr22132 or b5351

Read More
John -
October 06, 2013
A:

tried pulling the belt off and the motor starts and runs indefinitely without tripping the breaker. so either the motor is weaker than it was, or the load has increased somehow, though the fly wheel on the pump head seems to turn without much effort.

Read More
John -
October 07, 2013
A:

but i have no idea how much effort should be required

Read More
John -
October 07, 2013
A:

 

Thank you for your question.

 

I am sorry you are having a problem with the air compressor. I will be happy to assist you with determining the problem. I have seen this problem be caused by the pump. To be sure this not a pump problem, I recommend unplugging the unit from the outlet. Then remove the belt cover and walk the belt off the pulley. Once the belt is off, turn the large pump pulley by hand. If there is not any pressure in the tank, you should be able to turn the pulley without much resistance. If it turns without much resistance, the pump should be fine. The problem would be in the motor. I looked up the motor for your model and it is part number MO-6026. I am sorry the motor for the compressor is no longer available. Due to the way the motor mounts on this unit, I do not think any other motor will work. I wish I had better news for you.

 

 

 

Please let me know if you need further assistance.

 

 

 

Thank you for using Manage my life.

 

Mark. 

Read More
Mark T -
Sears Technician
October 07, 2013
A:

well, there is an amount of resistance that is too much for the motor and an amount that is not, and differentiating by feel doesn't seem too conclusive. I mean, with a 1 hp motor, i imagine it doesn't take much for that pump to become too resistive. a bad seal or something that i can't feel by hand would add enough resistance to draw more current from the motor I imagine. is there a more scientific way without tearing the whole pump apart? on the topic of motors, couldn't I just get my cobalt steel bit out and drill the one or two necessary holes in the base plate of this one? http://www.northerntool.com/shop/tools/product_200317561_200317561 not that i'm particularly interested in this particular brand

Read More
John -
October 07, 2013
See more answers
Q:

Vizio TV parental control password

A:

Some TV features are difficult to understand. I researched your question and found a good link that may help you reset the password on your television set. I attached the link below. I hope this helps!

Read More
Jacqueline S -
November 15, 2010
A:

I found this link as well - but I don't believe using 0000 will allow you to reset the code. I will try it again, but I believe using the 0000 code did not allow you into the menu. I believe the 0000 is the factory setting that can be used initially to set up the That way seems a bit too easy to override the parental control

Read More
Anonymous -
November 15, 2010
A:

Vizio has a few different parental universal unlock codes depending on the model number. The 5 most used that I know are:

2489, 5351, 8202, 8205, 8206

Hope these help get your TV unlocked.

Read More
Dusty J -
Sears Technician
November 18, 2010
A:

Thanks - tried the codes above over the weekend - second one let me in. Kurt

Read More
Anonymous -
November 22, 2010
A:

I am glad I was able to assist you. Have a great week. I also wanted to let you know you might get a survey in the next few days. You can always look at you question any time and rate it!

Read More
Dusty J -
Sears Technician
November 22, 2010
A:

Nice post.

Read More
Anonymous -
November 22, 2010
A:

Happen to have this problem with my HDTV. After calling VIzio, they tell me that I have to get a new Main Board. What can you expect, its money everyone wants, even though they say their main difference from other HDTV companies is customer satisfaction. What bs. I had to cut out my cable cause I couldn't afford it anymore and when I installed an HDTV antenna, when I realized I had this problem. Good thing I searched the info Highway. Thanks for the code that probably saved me the lack of a few channels. I hope others will search for a solution before they take up the wusa from VIZIO. Later

Read More
Anonymous -
April 29, 2012
A:

Dusty, thank you for the universal unlock codes!!!! Very helpful.

Read More
Anita -
October 11, 2012
See more answers