Model #5163 EUREKA Vacuum, Canister

  • Power Team Vacuum Cleaner Front Page
    3 Results
  • Base Assembly
    3 Results
  • Motor Assembly And Attachments
    3 Results
  • Powerbrush
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Replacing motor 15817530 Kenmore Kenmore sewing machine head

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about a part for your Kenmore sewing machine model 15817530. I am so sorry the motor needs to be replaced. As you noticed on our website, the manufacturer no longer makes this particular motor. Due to the age of the sewing machine, the replacement motors that were listed for it at one time are also no longer made. 

In this case you will have a few options.

1. Have the sewing machine serviced to see if the motor is repairable. 
2. Conduct an online search using the motor part number. Sears only offers parts that are guaranteed by the manufacturer to work with your product. Because we cannot guarantee an after-market part will work with your model, we do not list alternate parts. You can also look for a used part online. Again, there is no way to guarantee the condition of the part. 
3. Because of the age of this product, and because some parts no longer available, you may want to put your money towards a new sewing machine, rather than fixing this one. I have included the link below for you to see what is currently available. 

I am sorry I am not able to get the replacement motor you need. I hope this information helps. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
March 16, 2015
Q:

JMP31C L2CC Installation instructions

A:

I know how important it is to have as much useful information about your appliance as possible so that it is easier to find replacement parts and part numbers. While you are waiting for an expert answer, I did manage to find a link in where you can enter your model number and locate the installation guide from the Manage My Life website. Hope this helps!

Read More
Priscilla V -
January 06, 2013
A:

The screw kit did not accompany this drop in stove and was sent two weeks later by Sears store 770 426 6895 Appliance Dept Marietta Ga. The front lower trim kit requires three screws to fasten to stove. The shanks of the screws Sears sent me are too big to fit three holes at front bottom of stove (JMP31C L2CC). Where can I order the correct screws from? Installation instructions you recommended should help. Thank you for helping Priscilla V.

Read More
Barry -
January 06, 2013
A:

Hello Barry,

I'm sorry to hear that you have had difficulties with your new range and I would like to assist you. The installation guide for your range is here: Range Installation Guide. The screws that I think you are referring to are circled on the accompanying parts diagram attached to the end of this reply. Compare the part number of the screws that you received to this part number: WB01K5163 that is also subbed to the new part number WB1K5163. Please reply and let me know if you have the same part number or not and also verify if the screw that I have circled on the image is the one that you are referring to.

I look forward to assisting you further.

Jerry C

Read More
Jerry C -
Sears Technician
January 07, 2013
A:

The image did not post correctly, here it is full size.

Jerry C

Read More
Jerry C -
Sears Technician
January 07, 2013
See more answers
Q:

Wall Oven #9114712996

A:

I can see how disruptive this issue would be to have the oven heat up then shut off. I see there are other similar issues in the expert archives. I selected one that I thought may help find the cause and attached below. Hope this helps while you wait for the expert review your model.

Read More
Barbara H. -
May 29, 2011
A:

Unfortunately after ten years the model will no longer be available. meaning you can not purchase any parts for it either. Below I attached the link to the Sears.com website if you would like to purchase a new car carrier. I hope this information is helpful.

Read More
Jackie S -
May 29, 2011
A:

That type of failure is normally caused by a bad clock control board in the console. There is a possibility that a wiring failure could cause this problem. A temperature sensor would not normally cause this failure. It would not hurt to check that component. You can check the sensor probe by shutting off the circuit breaker for the range and accessing it as shown in the image below. Here is a video that shows how to test the sensor: Oven Sensor Testing . The sensor in this oven should measure around 1100 ohms at room temperature. If it is bad, replacing it may fix your problem. The part number for that sensor is WB21X5301. You can order that part from the Sears PartsDirect website. It costs around $75 so be sure that you tested it correctly before replacing this component. If the wiring on the control board is okay and the sensor is good, then you would probably need to replace the clock control board in the console to fix this oven problem. The clock control part WB27K5163 is no longer available as a replacement part. If that is the part that is causing this problem then the oven will need to be replaced. You can view current oven models on the Sears.com website.

Read More
Lyle W -
Sears Technician
May 30, 2011
See more answers