Model #4765 SOUND DESIGN Misc Audio

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore HE Front Loading Washer Question

A:

Thank you for your question.  I had some difficulty bring up the 110.4765* model number.  Please double check the model number and reply below with any additional details or changes.  A power failure error would usually be a PF and not just an F.  If your machine has a Drain/Spin cycle then try that first.  If the washer will spin then the drain motor and door lock are likely okay.  A Rinse Only cycle is a good test cycle.  It should fill, tumbler, drain and spin.  I hope this helps.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
October 06, 2013
A:

It fails at precisely 24 minutes every time. My washer doesn't give me the option of just doing a particular part of the cycle. It just gives me the choices of the type of load, e.g. normal/casual. The model number listed on the front of the book is 110.4756 or 4757. I copied it exactly as it is written, so i hope I got it right this time.

Read More
Lucy -
October 06, 2013
A:

The model 4756 will work. There should be a complete error code. The code would be something like F21, F01 or F20. If your washer has no display then the Status lights will determine the error code. The Add a Garment LED light being on would indicate an F01 error. The washer should have a dedicated Drain/Spin cycle. Th eimage below contains the instructions to enter and run a diagnostic test. Try the tests and see if any error codes are displayed.

Read More
Fred M -
Sears Technician
October 08, 2013
See more answers
Q:

Kemore HE2t Front loading washer. Cleaning the washer interior Model #110.4765

A:

I understand how important this is to know. The ManageMyLife website is a great place to find answers to questions that need qualified and insightful responses. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Dezeray -
March 04, 2013
A:

It will all end up in the tub with the same results so no worries about bleach in the detergent dispener. 

Read More
Fred M -
Sears Technician
March 05, 2013
See more answers
Q:

Garage door opener stops going up

A:

I am sorry that you are having some difficulties with your garage door opener and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your garage door troubles while you wait for your expert response.

Read More
Joseph P. -
September 20, 2012
A:

This type of problem is certainly odd. There are two possibilities you might check. Cold does affect the sensors and even though winter has not arrived,this should be considered. A more likely culprit is moisture on the sensors. If condensation is forming due to humidity or temperature, it may be affecting that first attempt to open.

I will be happy to continue research on this problem but if you will check tomorrow morning and advise, I would appreciate it. Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
October 11, 2012
A:

ahhhh!!!! good advise, where does one find (identify) the sensors

Read More
fred -
September 20, 2012
A:

I should have said the safety sensors. They are located on either side of the garage door about four inches from bottom. See image below.

Read More
Barbara H. -
Sears Technician
September 21, 2012
A:

Duh!!!! I must have been sleeping when I asked this as soon as I hit send I realized it was the safety sensors. I greased the drive gears and cleaned the sensor lenses. it has been great til this morning: 52 degrees and on first try it went up one foot. brought it down and 2nd try was OK. I am concerned with winter and colder temps on the way????

Read More
fred -
September 24, 2012
A:

Barbara H, any additional suggestions, having same issue today

Read More
fred -
September 25, 2012
A:

I am sorry for the delay. Your last response did not hit my e-mail as it normally would. The outside temperature should not be affecting it at 52 degrees. As it gets colder it would. For colder temperatures you can adjust the force up by one. That should help correct this type cold affected issue. I attached images below with the force adjustments. One other possibility is that the connections on the logic board may not be allowing enough electric flow the first time. The logic board is in the opener itself. The last image below can help. Check to see if any of the cold solder points show signs of cracking, corrosion or any damage. They may be able to be resoldered or you can just replace the logic board. I added the Sears Parts Direct link below. I hope this helps eliminate this issue once and for all. I will be checking daily for any additional posts, so let me know if this does not work and I will call in the cavalry.

Read More
Barbara H. -
Sears Technician
September 29, 2012
A:

Barbara.....well I have tried everthing as suggested. the logic board is amazingly clean, no "cold solder" points and all contacts are clean. I have greased the plastic gears as well. Now we have dropped to 47-65 degrees in the morning and it takes at least 4-7 times then up she goes. I am at whits end with this and my just have to look into a new opener??????

Read More
fred -
October 10, 2012
A:

Many homeowners share your frustration with this winter issue, as do I. Common causes are hardened grease in the tracks, misaligned sensors, moisture in the sensors or wiring issues to the sensors or control board. You have checked, cleaned and greased the tracks and working parts, checked the wiring and alignment. That leaves a bad logic board or a possible misalignment of the tracks themselves. Cold weather and use can strain metal. I would check the alignment of the sensors one more time to be sure, but it is likely the logic board or a alignment problem with the tracks. I would recommend having a professional technician check due to safety issues. They will replace the opener if needed or just make repairs if that is all that is needed. You can schedule at the link below if needed.

Read More
Anonymous -
Sears Technician
October 11, 2012
See more answers