Model #4700 DIRT DEVIL Vacuum, Canister

  • Assembly Schematic-4700/4750
    3 Results
  • Canister Schematic-4700/4750
    3 Results
  • Power Nozzle-4700/4750
    3 Results
  • Wiring Schematic-4700/4750
    3 Results
Find part by diagram >

Question and Answers

Q:

Replacement part for LG plasma TV 50PM4700UBAUSLLHR Lg Television

Q:

pilot light MI40T6FCX4-700

A:

Thanks for the inquiry and for being a valued member.

I am sorry to hear of the issue you’re having with the pilot going out. I know how aggravating that can be.

We don’t seem to recognize this Bradford water heater model, so we don’t have any of the specifics. This type of symptom typically indicates an issue with the thermocouple, or a restricted dirty burner, which you’ve addressed.

If you have not made any changes to area, where the water heater is installed or to the vent, I recommend cleaning the flame arrestor. The flame arrestor is a fine screen on the bottom of the water heater that can become plugged. If this happens, the combustion area will over heat and turn the pilot off.  I was able to find a service manual that shows how to clean the flame arrestor on many of these models.

Bradford Water Heater Service Manual

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
February 02, 2015
A:

Thanks for the manual, it covers what mine is with the Robertshaw gas valve. I have used an air compressor to blow out the screen on the bottom and inside as well. from the symptoms I don't think it is the thermalcouple unless the new one is defective,but if I can relight the pilot most of the time after a cycle. Seems to me something is cutting of the gas to the pilot are the thermalcouple and Thermal Switch the only safety items the turn off the gas ? Also the Thermal Switch can not be reset, the button doesn't push in at all ! can it be bypassed just for testing ? thanks for your help !!

Read More
wayne -
February 02, 2015
See more answers
Q:

Final Spin does not work NTW4700YQ0 Amana Automatic washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is not working properly.

 I recommend starting the diagnostics cycle to see if an error code comes up. 

ACTIVATING THE SERVICE 
DIAGNOSTIC TEST MODES
1. Be sure the washer is in standby mode 
(plugged in with all indicators off). 
NOTE: After initial power is applied, wait 10 
seconds before activating Service Diagnostic 
Test Modes.
2. Perform the following sequence of 
movement using the cycle selector knob.
NOTE: AFTER RESET, sequence “a” through 
“e” must be completed within 6 seconds. 
RESET - Rotate cycle selector knob 
counterclockwise one or more clicks 
to clear sequence.
a. Rotate cycle selector knob clockwise
one click and wait ½ second.
b. Rotate cycle selector knob clockwise
one click and wait ½ second.
c. Rotate cycle selector knob clockwise
one click and wait ½ second.
d. Rotate cycle selector knob 
counterclockwise one click and 
wait ½ second.
e. Rotate cycle selector knob 
clockwise one click.
?Successful activation of Diagnostic Test 
Modes will be indicated by all status 
LEDs (except for Lid Locked) flashing 
ON and OFF in half-second intervals.
NOTE: LED names may vary between 
makes and models.
 
? If the status LEDs do not display as 
described above, the sequence may 
not have been completed within 6 
seconds. Repeat step 2 to ensure this 
was not the cause. If still unsuccessful, 
see Unsuccessful Entry.

I have attached the diagnostics. If you do get an error code please resubmit your question. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
December 03, 2014