Model #4280 LXI Direct View\Digital 27" to 40" TV

  • Cabinet
    3 Results
Find part by diagram >

Question and Answers

Q:

Bearings bad on wm2455 washer, what parts do I order? wm2455hw

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

4280FR4048J 
4280FR4048N
 4036ER2004A

The parts listed are the bearings and seal that would need to be replaced. It is easier to replace the outer tub because it comes with the bearings installed. 
3045ER0048B is the outer tub.

 You can also visit searpartsdirect.com for parts, diagrams, and repair information.

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 26, 2015
Q:

washer and spin cycle smell something smoking. WM2301HR Lg Washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is not working properly.

 It sounds to me like it could be  a bad drum bearing causing your tub not to turn. 

Voltage Testing Hall Sensor at Stator:

If measuring voltage from the Main PCB Assembly to the Hall Sensor, use the
following steps:
1. Unplug power cord.
2. Remove rear washer panel.
3. Locate Hall sensor connector on the stator behind the rotor.
4. Place meter leads on terminals 5 to 4, white to gray.
5. Plug in power cord, close door, and press power button.
DO NOT PRESS START!
6. You should measure 10 to 15 Vdc. If 10 to 15 Vdc is present, control board, white wire, and gray wire are OK! If not follow testing output voltages on control
board in next section
7. To measure output signal voltage from the hall sensor, carefully move test leads to terminals 1 to 4, blue and gray. Slowly rotate motor rotor by hand. 
You should read a pulsing 10 Vdc. If 10 Vdc is measured from 1 to 4, move lead on blue wire to red wire, terminal 2. Repeat rotating motor rotor by hand.
You should read a pulsing 10 Vdc from red to gray.
8. If pulsing 10 Vdc is measured from 1 to 4 and 2 to 4, hall sensor is OK! If either test netted only 9 to 10 Vdc without changing (no pulsing) the hall sensor is
likely defective. Disconnect power by unplugging washer and ohm check hall sensor to verify failure of the hall sensor.


Cabinet cover:
1 Unscrew the 5 screws from upper of the canbinet
cover.
2 Unscrew the screw from filter cover.
3 Put a flat ( -) screwdriver or putty knife into the hinge
slots at the bottom of the cover and pry it out.
4 Unscrew the screw from the lower side of the cabinet
cover. 
5 Open the door.
6 Disassemble the clamp assembly
7 Tilt the cabinet cover.
8 Disconnect the door switch connector.
9 Lift and separate the cabinet cover.
10 Disassemble the clamp assembly.
11 Disassemble the gasket.
NOTE: When assembling the CABINET
COVER, connect the door switch connector.
10 Disassemble the clamp assembly.
11 Disassemble the gasket.

4280FR4048L  and 4280FR4048E  is the rear bearing for the tub. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 20, 2015
Q:

Jet engine taking off 79641383410 Kenmore Washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is making noises.

The jet engine sound will be coming from the rear bearing on the tub. When the rear bearing wears out it causes the jet sound.

 
4280FR4048Y is the rear ball bearing. I also recommend to replace the gasket with it.  MDS62058301. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
June 11, 2015

Top Accessories