Model #41799390110 KENMORE Laundry Centers/Combos

  • Drum
    3 Results
  • Blower And Base
    3 Results
  • Control Panel
    3 Results
  • Top And Cabinet
    3 Results
  • Washer-tubs, Hoses, Motor
    3 Results
  • Transmission
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore stackable washer dryer.

A:

ManageMyLfe.com is a great place to find your owner's manual and installation guides for appliances. I did some research and found the owner�s manual. I have attached the link below. Your expert will follow up and verify this information shortly. If you are having a specific problem please submit your question on the existing tread by click on the reply box below for your expert.?

Read More
Priscilla V -
October 31, 2011
A:

You can view the Owner's manual at the following link: Owner's Manual .

You can view the installation guide at this link: Installation Guide .

If you need service information I can most likely provide you with technical information showing how to access and change most parts.

Read More
Fred M -
Sears Technician
November 01, 2011
See more answers
Q:

INSTALLING FRIGIDARE DRYER PT# 5303272046 IN MODEL 41799390110 (THERMAL LIMITOR)

A:

Wiring can be difficult and is always important to put them in the proper location that they must go in. A suggestion that I have is for you to go onto the Sears Home Services website and schedule for a technician to fix the problem. I have attached the link below. Hope this helps! http://www.searshomeservices.com/repair

Read More
Alina F. -
October 22, 2010
A:

It does not matter which terminal you put the red/blk or brn/wht wires on.

If it blew when it was installed I suspect there is a voltage problem.

The red/black wire is feed by a relay on the main control. The relay is powered by the L2 black wire from the terminal block.

I'm wondering if anything has been replaced besides the thermal limiter.

This may need a volt meter to check if things went pop when the thermal limiter was installed.

Reply with a little more detail for further assistance.

Read More
Fred M -
Sears Technician
October 22, 2010
A:

I was replacing the dryer shaft bearing and shaft as well as the drum glide because of a recurring shrill noise when drying (mechanical problem) and ended up taking off the back panel (which should not have been necessary) without being able to see the wires which ran there. After replacing everything as I thought it should be, the thermal limitor (thermostat/thermistor safety) blew (electrical problem) when I attempted to run the dryer.. I rechecked all the wiring and confirmed that the only apparent problem was the thermal limitor/thermostat. Then I by-passed the thermal limitor/thermostat and the dryer worked. So, I replaced it, but it blew again! I have voltmeter. Thank you for your reply!!

Read More
GORDON -
October 22, 2010
A:

I've included in the image below what I believe is the wiring diagram for this elelctronic control dryer. From the description you give there is a short but I don't think it is a short with the limiter. See it this helps and let me know what else we can do to help resolve his problem.

Read More
Fred M -
Sears Technician
October 23, 2010
A:

Thank you again. The wiring diagram that came with the washer/dryer is attached as are photos showing the location of the part adjacent to the heating coil and the part itself. The part is called "thermostat, thermal limitor and thermistor safety. There is another fuse right next to it called "thermal light, thermal limiter/fuse", pt# 5303209192. I have no idea why the first keeps blowing, perhaps I should replace both? I am not proficient with wiring diagrams.

Read More
GORDON -
October 23, 2010
A:

Attached is a more inclusive scan of the wiring diagram, I hope.

Read More
GORDON -
October 24, 2010
A:

I am beginning to think that I reversed the wires from the "high limit thermistor" on the diagram with the wires to the "termal limitor" on the diagram. If I am correct, then the proper way to wire this is for the red and white wires to connect to part 5303272046 and the RED/BLK and BRN/WHT to connect to part 5303209192. Both parts are adjacent to each other, similarly named and have the same size quick connect fittings. I find no other solution so far. Is this a Eureka Moment?

Read More
GORDON -
October 24, 2010
A:

I believe you have problem figured out. One thing to realize is that the thermal limiter to the motor is a fuse that can be jumped/bypassed to check while the other is a thermistor which _can't be jumped._ If a thermistor is jumped or bypassed then it will be a direct short.

Read More
Fred M -
Sears Technician
October 26, 2010
A:

DEAR FRED M - JUST TO LET YOU KNOW THAT MY W/D WORKS JUST FINE NOW THAT I CORRECTED THE WIRING PER YOUR GUIDANCE AND IS RUNNING VERY QUIETLY WITH NEW SHAFT BEARING AND DRUM GLIDES. THANK YOU AGAIN FOR YOUR HELP. HAPPY HOLIDAYS!!

Read More
GORDON -
December 10, 2010
A:

Fred, I am back again. The dryer has stopped heating after 20-25 uses. It tumbles and everything else seems to work. There is continuity on the heating coil, the two thermal fuses are also in continuity and I also checked the continuity of the control thermistor - all ok. Any suggestions?

Read More
GORDON -
January 10, 2011
See more answers
Q:

How do I repair a leak on my Sears model 41799390110 washer that comes from where the tub to pump hose attaches to the tub?

A:

The hose is attached with sealant and if it's leaking then it's possible all that is needed to to redo the adhesive.

A part number for RTV sealant is 27615P and can be obtained from the following link: Sears PartsDirect .

The hose 5303931759 comes with sealant. See the 1st image below.

Your option is to try the sealant first and if the problem continues you might still have to replace the hose which may have a small tear that is not visible.

Accessing the hose is the other decision to make. If you can reach the hose from underneath then smear some sealant around the hose and see if the leak stops. It not then I suggest removing the spin basket to check the hose and apply more adhesive on the top side of the hose where is mounts in the tub. See the 2nd image for how to remove the spin basket.

I hope this information helps you resolve this problem but submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
August 08, 2009

Top Parts