Model #41744052400 KENMORE Residential Washers

  • Control Panel
    3 Results
  • Cabinet/top
    3 Results
  • Motor/tub
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore washer 417.44052400 will not spin in the spin cycle.

A:

Thank you for your question.  I am sorry about the spin problem on your Kenmore 417.44052400 Front Load Washer.   If the washer is tumbling in both directions in the wash cycle then the motor is okay.  If the water drains out but the washer does not spin then the usual suspect is the door lock assembly.  The door must be locked for the washer to spin.  The simple test is to run the diaganostic test.  The instructions are in the image below.  If the washe spins in the test then the door latch assembly should be replaced.  If it does not spin then there is another problem.  Try the test and see what happens.  You can reply below with any additional details for further assistance.    The do-it-yourself is possible but dealing with the door boot can be frustrating.   The 2nd image will give you an idea.  You can also have the problem repaired in your home by a Sear technician.  Here is the link: Sears Home Services Washer Repair.   I hope this information helps.  Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
August 28, 2013
A:

Fred, Your help was right on the button!! My wife (very non-technical) was able to perform the door latch test and inform me that the door latch was the problem. I picked up a new one on the way home and 10 later we had a fixed washer. Thanks, Jon

Read More
noodl -
September 05, 2013
A:

Glad to help and congratulations on a great self repair.

Read More
Fred M -
Sears Technician
September 08, 2013
A:

I am having this same problem, how do I run a diagnostic test? I also have an additional question does this model have a filter? I am asking because a ring went through the wash awhile back and was never found..Any ideas? Thanks

Read More
Jamey -
September 10, 2013
A:

Jamey, the instructions to run the test are shown in the image below. This particular washer does not have a filter but there is a hose from tub to pump you may want to check for the ring. The 2nd image below may be helpful fo you.

Read More
Fred M -
Sears Technician
September 15, 2013
A:

Hello everyone Having the same problem and before I could try the door latch test my father just cut the wire to bypass the door latch. Dont ask me but we still are having the the no spin thing happening. Looking for help please and thank u

Read More
Anthony -
September 25, 2013
A:

Anthony, By passing the door switch is not possible on this model. The control must see the door switch open and close or it will assume there is a door switch error. There is also a door lock circuit. If there is no spin but the washer will tumble in wash then the motor and speed control are likely okay. If the washer will spin in test mode then replacing the door lock assembly will most likely correct the problem.

Read More
Fred M -
Sears Technician
September 29, 2013
A:

Hello, I have the same problem. Can I get the instructions also? Thanks

Read More
CHRIS -
August 15, 2015
A:

I'd like to run the door lock assembly diagnostic test, but I can't seem to expand the image of the test sufficiently to read it. Please help.

Read More
Anonymous -
November 30, 2015
A:

Same model front load washer, replaced the control board but it will not tumble or spin. Help

Read More
joaquin -
February 02, 2016
See more answers
Q:

All writing disaapeared when wiping down front 41744052400 Kenmore Washer

Q:

washer stopping before finishing usually before softener cycle 41744052400 Kenmore Washer

A:

Thank you for your inquiry on your Kenmore Washer, Model: 417.44052400. From reviewing the details on your model, by what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer. If the lid switch is faulty, it will act as if the lid is not closed. On this model, make sure the lid hinge screws are tight. If the screws are loose, the hinge might not activate the lid switch. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced. To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the gray and tan wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

Safety Warning: Before beginning the repair, disconnect the direct power supply to the washer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

 

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
July 22, 2015

Top Parts