Model #41516114010 KENMORE Grill, Gas

  • Gas Grill
    3 Results
Find part by diagram >

Question and Answers

Q:

Adding a rotisserie to this model (415-16114010) ? 41516114010 Kenmore Gas grill

Q:

How to Install Gas Grill Igniter module?

A:

Thank you for your question and I understand your concern.

Unthread the collar and push button from the igniter and then you will likely see another nut to remove and then the igniter can be removed from back side of the control panel.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
August 13, 2013
A:

That's exactly what I tried to do, but there is insufficient clearance between the igniter module and the solid gas line going to each of the burner controls. I can not push the button portion of the igniter through the control panel. The gas line prevents it. Other suggestions?

Read More
Dave -
August 13, 2013
A:

Dave; If that's the case then you will need to remove the control panel or at least remove the screws securing the control panel and pull it out on the control panel enough to remove the igniter.

Read More
Joey S -
Sears Technician
August 14, 2013
A:

the knobs are either just pushed on and will pull off or they will have a set screw in them. just turn the knobs and look for a small set screw that takes a allen wrench. if you see no holes in the knobs they will just pull off. the set screws are usually always on the bottom of the knob.

Read More
Anonymous -
August 14, 2013
See more answers
Q:

Having burner issues and/or flow problem

A:

Having this happen to your appliance that we use on a daily base can be really concerning. While you are waiting on an expert to answer your question, I suggest you set service with a Sears technician. I have attached the link below. Hope this helps!

Read More
Dezeray S -
August 23, 2011
A:

There is no easy way to blow the gas lines out with air pressure. This is normally not a problem. The gas lines should not get blocked unless the gas valves have been left open for a long time.

The regulator has a safety cut off inside it that will shut the gas off if a hose breaks while cooking. If the cut off has tripped, you will get the symptoms you have.

To reset the regulator remove it from the LP tank and let it set for 10 minutes or so. Install the regulator on the tank and open the valve on the tank 1/4 turn. Open the gas valve on the grill farthest from the regulator for 5 seconds and turn it off. Do this procedure with all the gas valves then light the burners. If the burners work normally, open the tank valve to normal operation position.

If this doesn't solve the problem, you need to replace the regulator. The regulator only comes with the manifold and gas valves attached.

Read More
Jimmy K -
Sears Technician
August 25, 2011
A:

I have a Kenmore Elite 4-burner gas grill and had the same problems as described above. After following the "expert advice," the grill works perfectly! Could not be happier - especially considering the cost to fix the problem was zero. What a great country! Happy bar-b-cuing!!!

Read More
david -
June 17, 2012
A:

Hello David. Thanks for letting us know how this turned out. We are glad to hear that you got that situation resolved. Let us know if you ever need more help.

Read More
Lyle W -
Sears Technician
June 18, 2012
A:

I replaced my regulator, as that's what your repair guy said to do. But I still have a very low flame, and can't have all three on. what can I do my next step is to replace the burners.

Read More
Jim -
May 25, 2013
A:

I replaced my regulator, as that's what your repair guy said to do. But I still have a very low flame, and can't have all three on. what can I do my next step is to replace the burners.

Read More
Jim -
May 25, 2013
See more answers

Top Parts