Model #4030 UNIVERSAL RUNDLE Toilet

  • Replacement Parts
    3 Results
  • Color Chart
    3 Results
Find part by diagram >

Question and Answers

Q:

need part number for gsd4030z0ww gsd4030z0ww

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about the part for your GE dishwasher model gsd4030z0ww. I am so sorry you are having difficulty identifying the part.  I will be happy to help you with this.

Key 427 is the Wear Ring Base. It has been combined in to a kit with the Wear Ring (key 431) and the Pump Seal Assembly (key 434). The part number for that kit is WD19X62. These parts, along with the Nut Grater, Impeller Assembly, Blade and Shaft and the Sump Clamp fit between key 505 (Sump Inlet) and key 311 (Pump Assembly Housing. The Sump Inlet part number is WD18X213 and the Pump Assembly Housing is part number WD19X10013. In this case key 311 is no longer available. This means you will need to order the complete motor/pump assembly to replace key 311. The motor/pump part number is WD26X10013.

I hope this answers your question. Thank you for choosing Sears, we appreciate your business.

  

Read More
Rachel Morgan -
Sears Technician
October 21, 2014
Q:

can you use this model 4030L without useing the floor sensos 2040L Genie Genie ac beltdrive gdo

A:

The Managemylife web site is a good resource to find out what may be happening with your Garage Door Opener. I did some research for you at Managemylife.com and found an excellent article that also has multiple expert answers at the bottom of the web page that addresses the most common questions that have been asked by other members. I hope this will help until your expert can answer your specific question. I attached the link below. Tony, I also found this link on a Genie garage door opener that may help too.

Read More
James -
February 09, 2013
A:

Thank You for submitting your question.

I show the model number you provided does require the safety sensors. Newer models require safety sensors on all garage door openers. You face a significant legal liability by continuing to operate a garage door opener without the electronic reversing system. If someone were to be trapped by the closing door with a non-compliant opener on it there will be very little legal ground to stand on in your defense.

Read More
Desirea -
Sears Technician
February 09, 2013
See more answers
Q:

Trane 4TEE3F40A1000AA problem with the Air Handler. It blows the 5 amp fuse. Fan turns freely. Any ideas what is blowing fuse. It runs for days before blows.

A:

I understand how it can be frustrating when it comes to figuring out the issue to why the fuse keeps blowing on your air handler. While you are waiting for your expert answer, I did some research on your model. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within two business days with detailed information. Thank you for using Manage My Life.

Read More
Priscilla V -
January 02, 2013
A:

Thank you for using Manage My Life. The fuse is blowing because there is an intermittent short in the low voltage wiring between the thermostat, air handler, heat pump or with the ICM control, variable speed motor module or in extremely rare instances the transformer. With these scenarios it's best to have a qualified technician diagnose the problem as they will have the necessary tools to do so.

Read More
Andrew D -
Sears Technician
January 03, 2013
A:

OK thank you. I could send you the wiring diagram . I just scanned the circuit diagram and attached it to this conversion. I highlighted the fuse that is blowing.

Read More
Fred -
January 02, 2013
A:

Thank you for using Manage My Life. The fuse is blowing because there is an intermittent short in the low voltage wiring between the thermostat, air handler, heat pump or with the ICM control, variable speed motor module or in extremely rare instances the transformer. With these scenarios it's best to have a qualified technician diagnose the problem as they will have the necessary tools to do so.

Read More
Andrew D -
Sears Technician
January 03, 2013
See more answers