Model #376110 POULAN Walk Behind Lawnmower, Gas

Find part by diagram >

Question and Answers

Q:

Table saw not working

A:

I understand how difficult it can be to try to cut things with your table saw not properly working. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
January 27, 2012
A:

You can't tell visually if the relay or the capacitor is bad. Sometimes the capacitor will leak a white powder when it fails, but not always. You can order the capacitor at Parts Direct The part number is STD376110 and the price is $8.95. You can probably find the start relay at WW Grainger. Many products use the current relays like your saw has. Get the information off the relay and go to www.grainger.com to see a catalog.

Read More
Jimmy K -
Sears Technician
January 30, 2012
See more answers
Q:

Table Saw Circuit Breaker

A:

Definitely having to find parts for your Table saw can be a challenge to help in determining if you have the right part I would suggest visiting Sears parts direct.com where you can view a diagram of all parts available for your tractor. I have attached a link below. Hope it helps!

Read More
Priscilla V -
November 28, 2011
A:

I have chatted with Sears parts on line. I have looked at the manual and parts lists. The parts line says they are not available, the parts drawing does not list the part. For a $3.00 part a perfectly good saw will not run. Well it runs, but it does not have a circuit breaker in-line now. So I do not burn out the motor I would like to replace it.

Read More
mark -
November 28, 2011
A:

Thank you for your question on the Klixon reset for the motor.

I will need the Emerson motor number to tie the reset button for searching.

Please check the Klixon number again as I was not able to find it by the number search in the Klixon parts suppliers.

Please let me know what you find.

Sam A.

Read More
Sam A -
Sears Technician
November 30, 2011
A:

Hi Sam, I found the same thing in researching the part. Not knowing much about electronics I had no idea which reset would be the same. Here is the info off the motor id. Part # 62505 MFG Model KS48YXEK-198 120 Volt 12 Amp RPM 3450 HZ 60 insul Class B AMB 40 Deg C PH 1 MFG NO. 381 7 E22922 The next problem is once you find a matching part is where to purchase it. Thanks for the help, Mark

Read More
mark -
December 01, 2011
A:

Thank you for the update on the table saw motor reset. I did find a source for you. Call a company that took over the Emerson Electric motors. EIS @ 1-800-322-4702 and talk to Debbie. I hope this will help. Sam A.

Read More
Sam A -
Sears Technician
December 01, 2011
A:

HI Sam, It took a few days to contact Debbie but finally talked to her. She told me she did have the circuit breaker I needed. One was $75 and 2 were $84 dollars so I got ordered two. Before they arrived the saw died and I believe needs a capacitor. With the price of the breaker and now a capacitor I went out and bought a new Craftsman table saw. I think the old one was a better quality than the new one, but now I have a lighter one that has wheels to roll on. Thanks for the help, and as usual for me a day late and a dollar short. I am attempting to return the parts, I have not opened the package. Mark

Read More
mark -
December 14, 2011
A:

Mark, I believe you and I have the same (or very similar) older Craftsman table saws. Just so you know, the capacitor is only $8 from Sears or $5 from Grainger. Also, the circuit breaker (Sears calls it a "Protector) is $38 each from Sears Parts Direct. Not sure where you live, but if you're anywhere near the Twin Cities I'll gladly pick up you old Sears saw if you have given up on it. I could use the parts, if nothing else! Dave

Read More
Dave -
January 06, 2012
A:

Protector: Sears part # 74383, $38 @ Sears Starting Relay: Sears part #62453 (no longer available, but I'm told equivalent relays are available if you go to an electronic parts store) Capacitor: Sears part # 376110 107-129MFD $9 (alt: Dayton 2mdr1 108-130 MFD, $5 @ Grainger Good luck!

Read More
Dave -
January 06, 2012
A:

I'm trying to find an owner's manual, but no luck. Do you still happen to have your manual, by any chance? I also have model # 113.295752.

Read More
Dave -
January 06, 2012
A:

Thank you for the update on the table saw. The manual can be ordered from Sears Parts direct. I am sorry that we did not have this manual in the MML site for downloading. Click on the link below for the ordering of the manual. Sam A.

Read More
Sam A -
Sears Technician
January 06, 2012
See more answers
Q:

why won't my tabel saw start?

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Barbara H. -
November 17, 2011
A:

I am still waiting for my expert to contact me. It is now 9:12 am on 11/18/11.

Read More
john -
November 18, 2011
A:

Thank you for your question as to why the table saw will not start after pinching a board.

On some of these old direct drive table saws that can be a show stopper if the circuit breaker does not trip soon enough.

Make sure that you have power to the outlet you had the saw plugged into.

Please press the reset button again if you have not done so recently. It may have been to hot to reset at the time it tripped.

There is a capacitor inside that control box and also a start rely.

Any one of those may have failed.

I would suggest that you open up the control switch box and test or have tested all the components in the box.

If you have a volt/ohm meter you can check the capacitor and the start and overload switch for continuity.

For the On/Off switch, make sure you have at least one wire off the switch and the switch turned on to check to see if the internal contacts are completing the circuit.

The over load the same way.

The relay you will not be able to check very well, but if you shake it and it rattles it probably is okay.

The capacitor you can check also but again with at least one wire off one of the terminals and set your meter to the lowest ohm scale and you should get a reading across the terminals and then it should go away. Reverse the meter leads and it should do the say thing again. If it does that is it good. If it does not give you a reading you will need to replace it.

The number for the on off switch is:62442. The part number for the overload is:64383. the capacitor is part number STD376110.

[Table saw parts list | http://www.searspartsdirect.com/partsdirect/part-model/Craftsman-Parts/All-Products-Parts/Model-113298051/0247/0731750?pathTaken=&prst=0&shdMod=113298051].

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
November 19, 2011
See more answers

Top Parts