Model #36275581891 KENMORE Free Standing, Gas

  • Gas & Burner Parts
    3 Results
  • Control Panel & Cooktop
    3 Results
  • Body Parts
    3 Results
  • Door & Drawer Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore gas range

A:

I think its great that you are wanting to do some repairs on your own and I will be happy to help. I did some research and I was able to find a link that will guide you in making some checks on your range. I hope this helps with your range repairs while you wait for your expert response.

Read More
Joseph P. -
December 18, 2012
A:

Thank you for your question and I understand your concern.

The oven gas opens by amperage/current and not voltage. The glow bar igniter pulls resistance and if it pulls enough resistance it will cause the oven gas valve to open. If the igniter is weak and not pulling enough current/amperage, the gas valve will not open. I added an image below with the Oven Burner Ignition System theory of operation.

NOTE: Do not apply 120 volts across the terminals on the gas valve or it will burn it out and it will have to be replaced.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 19, 2012
A:

Excellent. A schematic was what I needed. Thanks!

Read More
Vic -
December 21, 2012
A:

VIc; Your welcome. Have a Happy Holiday.

Read More
Joey S -
Sears Technician
December 21, 2012
See more answers
Q:

Oven doesn't heat up fast enough.

A:

With the oven not heating properly can cause quite a delay when it comes to preparing a meal. After researching the Manage My Life website and have located a link similar to your issue. While you are awaiting a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
September 09, 2012
A:

That link for a previous answer that Priscilla V. posted in the above response describes one possible cause for your failure. You could have a weak igniter on that bake burner. Here is a video that illustrates the ignition process in your range. If that igniter is glowing constantly when the range is heating up initially then there is a good chance that you have a weak igniter. You can switch the bake and broil igniters as described in that previous answer to see if that fixes your problem. If that igniter is bad, then you can order a new one from this page: Igniter for Kenmore Range Model 362.75581891 . Be sure that you unplug the range before accessing and replacing internal components.

Since the oven maintains the proper temperature once it gets to the set temperature, you could also have a problem with the electronic oven control board (part WB27K10142). If that igniter is shutting off before the oven reaches the set temperature during the pre-heat process then you will probably have to replace that control board in the console. You may also need the overlay (part WB11K10005) if you replace that control board. As noted above, be sure that you unplug the range before accessing internal components.

The image below shows how to open the console on your range if you need to replace that control board.

These tips may help you fix this oven preheating problem yourself. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician examine the range and fix this problem, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 11, 2012
See more answers
Q:

Wiring - Kenmore model # 362-7558-1891

A:

An expert shall have an answer to your question within 24 to 48 hours. Have a great day.

Read More
Alina F. -
January 13, 2011
A:

I provided a wiring diagram in the first image and a schematic diagram in the second image. The third image shows some additional information about the control board.

This should help you with the wiring that you need to complete on the range. Be sure that you unplug the range to disconnect electrical power before accessing internal components.

If you need more help, reply with additional details and we will assist you further.

NOTE: Be sure that you connect the wires properly. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 14, 2011
See more answers

Top Parts