Model #36275321003 KENMORE Free Standing, Gas

  • Gas & Burner Parts
    3 Results
  • Control Panel & Cooktop
    3 Results
  • Body Parts
    3 Results
  • Door & Drawer Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Wiring diagram

A:

I hope this article is helpful until your expert researches the wiring diagram for you. I have attached the link below.

Read More
James -
January 17, 2012
A:

I provided a wiring schematic and wiring diagram for this range in the image below. NOTE: This information is intended for technicians. Follow electrical safety guidelines when using this data. Unplug the range before accessing internal components.

If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
January 18, 2012
See more answers
Q:

Kenmoor gas oven not heating up to set temperature

A:

I understand how vital it is for your appliances to operate properly. While you are waiting for your expert answer, I have found a link that will provide some information and troubleshooting for the problem. I would suggest that you check the ignitor. Make sure it is cycling properly for the temperature. I hope this helps.

Read More
aashe -
August 19, 2011
A:

You could have a bad electronic control board in the console that is causing this problem. Since the oven will heat better at the higher setting, you could have a problem with the oven temperature sensor probe. You can unplug the range and access the control as shown in the first image below. That image shows the wiring diagram for the oven portion of this range. You can measure the resistance through that temperature sensor circuit using a volt/ohm meter. That sensor circuit should measure around 1091 ohms at room temperature (75 degrees). If the resistance is more than 5% off, I recommend that you check the resistance directly at the sensor (with the range still unplugged ). The second image shows how to access the sensor. Here is a brief video that shows how to test that sensor using a volt/ohm meter: Oven Sensor Testing . If the sensor is bad, it will need to be replaced. The part number for the sensor is WB21X5301. You can order it from the Sears PartsDirect website.

If that sensor is okay, you have a problem with the wire harness if that resistance through the sensor circuit measured directly from the control board is bad.

If the entire sensor circuit resistance is okay, then you will probably need to replace that control board (part WB27K10141). Be sure that you have the range unplugged when accessing internal components.

If you need more help, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 22, 2011
See more answers
Q:

KENMORE GAS RANGE OVEN WONT LITE MO#362.75321003

A:

Diagnosing oven issues can be frustrating. I can see you have replaced several parts. While you wait for the expert to review the work completed and respond, you can check a previous expert answer for this issue and model. I attached the link below. Hope this helps.

Read More
Barbara H. -
June 18, 2011
A:

Thank you for your question.

I can understand your concern when the range did not work very long after you did the repair.

This symptom is usually related to the igniter and or the safety valve.

Even though you see the orange glow of the igniter it still may be the problem.

What I would suggest you can do is to exchange the broil igniter with the bake igniter to see if you have to go farther and replace the safety valve.

The two igniters are the same so you can help diagnosis the range without spending any money.

NOTE! The igniters are fragile so be carefull when handling them.

I hope this helps and if you need more help please reply and I will be happy to help your further.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
June 20, 2011
A:

hi sam i did change out the broiler igniter.and the oven lites now.thanks for the info .we dont use the broiler anyhow.

Read More
charles -
June 20, 2011
See more answers

Top Parts