Model #36275275692 KENMORE Free Standing, Gas

  • Gas And Burner
    3 Results
  • Cooktop
    3 Results
  • Body
    3 Results
  • Door And Drawer
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven won't light 36275275692 Kenmore Gas range

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Sherman_G_Wallace -
Sears Technician
May 14, 2014
Q:

Convert Kenmore 36275275692 from lp to natural gas to operate at 11000ft

A:

I can understand your concern over wanting to know how to convert your gas range from LP to natural. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
October 15, 2012
A:

A qualified installer should complete that conversion.

I provided information about the orifices and the LP conversion of that range in the image below. The LP conversion process will need to be reversed. You can check to see if the natural gas orifices were saved in the location shown at the top of that image.

You can order new orifices from this page if necessary: Kenmore Range Model 362.75275692 Gas and Burner Parts .

The orifices for the burners will need to be changed and the burners will need to be adjusted. The regulator will need to be converted back to natural gas. The orifice spud on the oven burner will to be backed off to the natural gas position. The oven burner will need to be adjusted as shown below.

This information should help the installer properly convert that range and adjust if for the altitude.

If you need more assistance, reply with additional details.

You can contact your local gas supplier for a qualified installer to convert the range to natural gas. You may also be able to find a pre-screened service provider through the ServiceLive.com website.

Read More
Lyle W -
Sears Technician
October 17, 2012
A:

Lyle, thanks for you informative reply. Since I don't live at the location where the stove is, and don't know if the natural gas orifices are there. So I plan to buy a new set just in case they are not. Problem is that the link you provided shows the parts but does not tell me which orifices are for natural and refers to numbers on the diagram, such as 3A, that don't show on the diagram. So I don't know what to order. Could you please give me a list of part numbers and how many of each. I know that two are the same. Just don't know which two. Many thanks for your help.

Read More
Mike -
October 17, 2012
A:

Just thought. The standard natural gas orifices are for near sea level operation. Don't I have to derate for 11000ft altitude to get proper combustion by using a smaller orifice the same as I do for a gas furnace? I was 20 years in the heat and air business.

Read More
Mike -
October 17, 2012
A:

You are correct about the smaller orifices. The Left Front and Left Rear burners will use the 1.44mm natural gas orifice (part WB06X0094). The Right Front burner uses a 1.65mm natural gas orifice (part WB02X9841). The Right Rear uses the same 1.07mm natural gas orifice for high altitude (part WB28K141). The oven burner orifice spud will need to be backed off less turns for high altitude. The normal adjustment on that oven burner is about 2 1/2 turns. The installer will probably need to experiment with that adjustment on the oven burner to get it adjusted properly. NOTE: An installer from your gas supplier may have the orifices or may be able to drill them based on the size information provided above. You may want to check that issue before ordering the parts. Let me know if you need more help.

Read More
Lyle W -
Sears Technician
October 17, 2012
See more answers