Model #3627526890 KENMORE Free Standing, Gas

  • Burner Assembly
    3 Results
  • Control And Cooktop
    3 Results
  • Cabinet Parts
    3 Results
  • Door And Drawer
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven won't light 3627526890 Kenmore Gas range

A:

You could have a problem with that timer if the oven burner won't light in the timed bake or clean mode. The buzzing is likely caused by the transformer. A problem with the oven control thermostat, the igniter or the safety valve could prevent the oven from heating in the normal bake mode. Try the oven in several different bake and broil modes. 

 

If the igniter glows but won't light the burner in the normal bake mode then the igniter will likely need to be replaced again. Don't touch the element of the igniter with your bare fingers when replacing that components. Oil from the fingers can cause premature failure of the igniter.

 

If you need more help, reply with additional details and we will assist you further. 

Read More
Lyle W -
Sears Technician
December 02, 2013
Q:

Gas oven won't work

A:

Good morning... I can fully understand your concern regarding this issue. I did locate a link that will discuss this situation in greater detail. Though this link discusses a different model number, the mechanics are likely going to be very similar. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might be wrong with your oven and have a nice day.

Read More
Henry -
February 05, 2013
A:

Thank you for your question and I understand your concern.

Before the oven will attempt to heat, the glow bar igniter must be supplied with 120 volts when the oven thermostat is turned on. Since the igniter is not glowing, it could just have a broken igniter or a faulty oven thermostat. You can remove and disconnect the igniter and test it for continuity with an Ohm meter. NOTE: Disconnect the power cord from the power source before accessing and disconnecting the igniter.

If the oven igniter measures resistance, I suspect a faulty oven thermostat. There is also an oven safety valve that the current must flow through or the igniter will glow because the path of voltage is not passing through the oven safety valve.

I added an image in my second reply to reference.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
February 05, 2013
A:

Kay: I added an image below with the theory of operation and how to access the igniter and oven thermostat. Disconnect the power cord from the power source before servicing.

Read More
Joey S -
Sears Technician
February 05, 2013
See more answers
Q:

Gas stove, model # 362.7526890, won't light.

A:

Gas stoves are great to cook on. It can be a frustrating the there is a the problem with the burner. I found some information for you that I am hoping will help you out. I am adding the links below to help you with your question while you wait for your expert response. I do hope that this will help you out.

Read More
Marc H -
May 14, 2012
A:

Thanks, Marc. Definitely isn't a gas flow problem, but could potentially be the spark module. Thanks.

Read More
mikehamm -
May 14, 2012
A:

Thank you for your question and I understand your concern.

The electrodes do not need replacing unless the ceramic insulator is cracked. A cracked or broken ceramic base will cause the voltage to jump to grounded top instead of jumping to the grounded base/burner cap. If the spark electrode wires are damaged, the voltage can jump through the insulated wires and arc to ground. So, it is important the burner base/cap is making a good contact to the grounded top or it will jump spark to the nearest available ground.

I added an image below with some useful information.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 17, 2012
See more answers