Model #3627361893 KENMORE Free Standing, Gas

  • Burner Section
    3 Results
  • Main Top Section
    3 Results
  • Cabinet
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

how do I know if the oven temperature sensor in malfunctioning? 3627361893 Kenmore Gas range

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your range. Upon researching model 3627361893; you can unplug the range power cord and remove the oven sensor when the oven is not hot. With the sensor removed test the sensor for continuity using a multi meter if the sensor reads no continuity then it may need to be replaced, if the test reads continuity then the sensor is ok. I have posted a link of the sensor to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
March 29, 2015
Q:

kenmore 400 series 11067432600 Kenmore Residential dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com! 

Read More
Anna T -
March 15, 2013
A:

Thank You for Submitting your question to ManageMyLife.com

I can understand the frustration when your dryer is not working correctly. The dryer should not have been heating when set to Air Fluff. If the dryer was heating when set to Air Fluff could indicate a shorted heating element (part number 279838) or a stuck heater relay apart of the Timer (part number 8299779) If you have further questions please let me know.

Thanks for using ManageMyLife.com

Read More
Desirea -
Sears Technician
March 15, 2013
A:

I replaced the control timer is there a way to check it?

Read More
chris -
March 15, 2013
A:

If you recently changed the timer then I would check the heating element and/or the thermostat. The thermostat controls the heating element and tell it when to turn on and off.

Read More
Desirea -
Sears Technician
March 15, 2013
A:

also when you turn the control timer to what setting you need the heating element heats up without pushing the start button

Read More
chris -
March 15, 2013
A:

should the heating element heat up when you turn the controled timer to the setting you want with out pushing the start button ?

Read More
chris -
March 18, 2013
A:

Thanks for providing the model number. I was able to locate the thermostat also known as the temperature sensor. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page. The instructions for replacing the temp sensor are down below as well.

 Temperature Sensor for Model 362.7361893

Instructions

1
Pull the range away from the wall, then unplug it from the wall outlet. Turn off the gas supply by turning the handle on the gas supply valve clockwise until tight.

2
Open the oven door and remove the oven racks.

3
Locate the oven sensor on the rear wall of the oven. Remove the screws or other mounting hardware securing the sensor to the oven wall.

4
Pull the sensor away from the wall gently, pulling the wire with it. If the wire connector does not pull through the rear wall, remove the large rear panel of the oven by removing the screws securing the panel to the cabinet. Unclip the wire connector, then feed it through the wall and remove the sensor.

5
Connect the wire connector on the new sensor to the range wire harness, feeding it through the rear wall if necessary.

6
Secure the new sensor to the wall using the mounting screws that secured the old sensor.

7
Replace the rear panel of the range, as well as the oven racks. Close the oven door.

8
Turn on the gas supply valve, then plug the oven's power cord into the wall outlet.

Read More
Desirea -
Sears Technician
March 18, 2013
See more answers
Q:

the oven wont get up to heat but it will heat to 250 when st at 400

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
James -
March 16, 2013
A:

Thank You for Submitting your question to ManageMyLife.com

I can understand how frustration it can be when you oven doesn't get to the correct temperature.

I would be happy to look up instructions and the part information. Could you please provide me with the model number so I can assist you further?

Look foreward to hearing back from you.

Desirea

Read More
Desirea -
Sears Technician
March 17, 2013
A:

362.7361893 the parts store said to put a new ignitor on it because the burner would light and stay lit till the temp would hit 180-200 then shut off the burner he said he thought it ignightor was not putting out enough volts to keep the gas valve open so i put a new one on now the temp inside oven 120 maybe the oven temp reads on the oven display reads425 and shuts off burner is it now the thermostate???? why now did it change thank you for your help

Read More
teege -
March 17, 2013
See more answers