Model #3627334190 KENMORE Free Standing, Gas

  • Burner
    3 Results
  • Control Panel
    3 Results
  • Body
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

gas oven does not come on 3627334190 Kenmore Gas range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the range.
 
Glad to help out.   Im  looking at your Kenmore Gas range model number 3627334190.

You say you purchased a new glowbar/ignitor for the bottom bake of the oven.   When you turn the oven on to bake, do you hear the "click" sound.    First we need to make sure that you have received a good bake ignitor.    Part number is 
WB2X9154.   If you don't hear the click then it is either a bad ignitor or it is wired in wrong.   Check the wiring.

If you are getting the click and find the ignitor is good then you need to look at the tube the ignitor is connected too.   See if there are port holes that you can take a brush to and clean it out.   That tube is no longer available so hopefully you can clean it out.


 Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
April 28, 2014
Q:

Kenmore gas stove, the oven won't work but burners do work

A:

For a great home cooked meal it is important to have your stove running. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. I hope the links that I provided are helpful. Have a great day!

Read More
Alina F. -
February 02, 2012
A:

Thank you for your question and I understand your concern.

If the broiler will ignite but not the bake burner, I would suspect a faulty glow bar igniter. The bake burner operation works like the broiler operation. Open the oven door and turn on the broiler. You will see the glow bar igniter begin to glow red and once it gets red hot and pulls enough current/amperage (min of 2.5 amps), the oven gas valve will open and the burner will ignite.

In order to access and see the bake igniter, the oven floor will need to be taken off. Open the oven door and remove the racks, remove the two screws at the back of the oven floor. Lift the back of the oven floor up, slide it back in order to clear the front lip and remove the floor. You will see another panel (flame spreader) that will need to be taken off to access the glow igniter. If you find the glow bar glowing, it is likely too weak to pull enough current/amperage to cause the gas valve to open. If the igniter is not glowing, it could be broken or it may have faulty selector switch or thermostat.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 04, 2012
See more answers
Q:

Are the broiler and oven jets changed from propane to natural gas by adjustment of the orifice spud only?

A:

Loosening the orifice spud the two turns will allow the higher gas flow rate needed for natural gas in the broiler and oven burners. The spud is actually a cover over a needle. Loosening the spud enlarges the opening around the needle to allow the higher gas flow.

You may also need to adjust the air shutter on the burner. Harsh, blowing flames indicate to much primary air flow. Reduce the size of the shutter opening to correct this condition. Soft, yellow flames indicate too little primary air flow. Open the shutter to correct this type of condition.

A combination of spud and shutter adjustments may be needed to achieve the proper flame height for natural gas operation of the oven and broiler burners.

Read More
Lyle W -
Sears Technician
May 23, 2008