Model #3627132190 KENMORE Range (gas)

  • Burner Section
    3 Results
  • Main Top Section
    3 Results
  • Cabinet
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

no gas to oven

A:

Oven are the main appliance in our so without Ovens we wouldn't have hot meals. While you are waiting on an expert to response to your problem, I have found some great links in the Manage My Life website. I have attached the links below. Hope this helps!

Read More
Dezeray S -
March 14, 2012
A:

Thank you for your question and I understand your concern.

If the surface burners will ignite but not the oven, check to see if the lever on the gas regulator has been flipped to the OFF position. See image below for additional information. If the lever is in the "ON" position, then the oven safety valve is not likely opening because of a weak glow bar igniter assuming the bake igniter is glowing. If the igniter is not pulling enough current/amperage, the oven safety valve will not open. The image below also has the theory of oven operation.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
March 15, 2012
A:

well, I found the valve and moved the lever 90 degrees. Still no gas. I left the igniter glowing for two minutes. No gas. This range was left unused for about a year in deep South Louisiana. Could the disuse, and extreme humidity cause something to stick?

Read More
Jim -
March 17, 2012
A:

Jim: I suspect the glow bar igniter is too weak to cause the oven safety valve to open. Replace the bake igniter and your gas valve will most likely open and let gas to the bake burner. The oven igniter is part #WB2X9154.

Read More
Joey S -
Sears Technician
March 19, 2012
See more answers
Q:

I have a Kenmore gas stove that after the power went out, only the top 4 burners will work. The Oven will not ignite. I have checked for a 'reset' button and or

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide a little more information such as the make and the model # of your product so your expert will be able to provide you the best possible answer. Just click on reply below and the provide the required data.

Read More
Dezeray S -
June 27, 2011
A:

Thank you for your question and I understand your concern.

Having the model number of your Kenmore gas range would have been helpful in providing model specific troubleshooting assistance. I must assume the electricity had been restored before trying the oven. The oven igniter must be supplied with 110-120 volts before it will glow.

I must assume your oven has an electronic oven igniter. The igniter must glow red hot and it must pull enough current to cause the oven gas valve to open let gas to the burner. If the igniter is not glowing the oven gas valve will not open. If you have a broiler drawer then the oven will only have one burner and one igniter.

Reply with the model number and additional details if you need any model specific information.

Read More
Joey S -
Sears Technician
June 27, 2011
A:

Thanks Joey S and your correct! I forgot to put that model number in. Kenmore Mod# 362-7132190 From doing my own inspection and looking at Kenmore's wiring diagrams, I came to the same idea that there is only one ignitor,and burner. Yes, to answer your question about the power being restored, breakers working correctly as well as the plug in power outlet. Not 'clicking' or actuation noise coming from the oven knob nor glowing of the ignitor like you mentioned. So now I'm not sure which to replace. Thanks for the help folks!!

Read More
Patricia -
June 27, 2011
A:

Patricia: Thanks for the mode number. First, make sure the clock is set and that both start and stop knobs are in the out position and not pushed in. If the start and stop timer knobs are pushed in, the oven will not come on. The glow bar igniter should be disconnected and tested for continuity using an ohm meter. The oven bottom can be taken out for easier access to the glow bar igniter. Disconnect the glow bar igniter and test it for continuity. You will likely find that it measures no continuity meaning it is broken. Note: Be sure to unplug the range before disconnecting the glow bar igniter. You will find the igniter mounted on the side of the burner near the back of the burner where it curves downwards. The igniter is part #WB2X9154 and I also added 3 images below to reference.

Read More
Joey S -
Sears Technician
June 28, 2011
A:

Thanks Joey S. The clock face is a single unit with just a timer on it. No additional knobs to mess with. I did however check to see if that button/knob was out for which it was. I will test the igniter as suggested. If the igniter is working properly, what should the ohms read be??? then, if that is in working order where should I go next? Would the single oven knob be another possible answer? and to check for continuity, what should that reading be? Thank you...

Read More
Patricia -
June 28, 2011
A:

Ok...just read what the igniter should read when it's being tested...thank you again

Read More
Patricia -
June 28, 2011
See more answers
Q:

What could be wrong if the oven on a 362.7132190 gas range doesn't work?

A:


The ignitor is the most likely part to fail when you have this problem. It would be best to test the ignitor for continuity before replacing it. If it is bad it will read open.

Read More
expert -
Sears Technician
February 22, 2008