Model #358795580 CRAFTSMAN Line Trimmers/Weedwackers, Gas

  • Drive Shaft And Cutting Head
    3 Results
  • Fuel Pump Assembly
    3 Results
  • Engine
    3 Results
  • Carburetor
    3 Results
  • Cuttting Head
    3 Results
  • 3 Version Cutting Head
    3 Results
  • Driveshaft
    3 Results
  • Crankshaft/crankcase
    3 Results
Find part by diagram >

Question and Answers

Q:

I am looking for a diagram of the fuel lines use in a Searw Weedwhaker model 358.795580. Including the in tank fuel filter, fuel lines to carburator and primer.

A:

Detailed instructions and diagrams can really come in handy when doing some major repairs and I will be happy to help. I did some research and I was able to find a link that will guide you with your project. I hope this helps with your repair, while you wait for your expert response.

Read More
Joseph P. -
July 10, 2012
A:

Thank you for your question on the string trimmer model fuel lines.

I will also give you a video on how to replace the fuel lines on a string trimmer.

U-tube video on replacement of the fuel lines .

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
July 13, 2012
A:

Sam A, the video is missing can you re-post please, thanks

Read More
Michael -
July 20, 2015
See more answers
Q:

Craftsman WeedWacker Model 358.795580 won't run.

A:

Thank you for your question.  I am sorry you are having a problem with your Craftsman line trimmer model 358.795580.  I will be happy to assist you with replacing the fuel pick up and lines. If you do not have the replacement parts, yet you can order them from the following link. Replacement parts for Craftsman trimmer model 358.795580. Once you have the parts, you can click on this link to watch a video on how to replace the fuel lines. The pick up line should be left long enough so the filter can move around the tank to stay submerged in the fuel.  I hope this is helpful. Please let me know if you need further assistance.  Thank you for using Manage my life.  Mark T.

Read More
Mark T -
Sears Technician
July 17, 2013
A:

I know how important it is to have a good working Weed wacker in your home so that you can keep your lawn maintained. While you are waiting on an expert to answer your question, I found a great link in the ManageMyLife website on your question. Click here. Hope this helps!

Read More
Dezeray S -
July 17, 2013
See more answers
Q:

32 cc Weedwacker Model 358795580 Ignition Module Replacement

A:

I found some information for you that I am hoping will be able to help you. Please click here:[Replace Ignition Module]. Your expert will also help answer your question. It may take two business days for your expert to reply. I do hope that everything works out.

Read More
Marc -
May 07, 2013
A:

Thank you for your question.

 

I am sorry you are having a problem with the trimmer. I will be happy to assist you. I found a great video that shows how to access the ignition module. The video is on a starter string but the steps are the same for accessing the module. Click here to watch the video. Once you have the unit apart remove the old module. When you install the new module, place a .010 in feeler gauge between the magnet on the flywheel and the legs of the module before you tighten the screws. This sets the air gap. Once you have the module mounted just reassemble the unit and check the operation.

 

I hope this is helpful. Please let me know if you need further assistance.

 

Thank you for using Manage my life.

Mark. 

Read More
Mark T -
Sears Technician
May 09, 2013
A:

Ok, so the video describes removing two clutch plates from a Ryobi trimmer by hitting a screwdriver with a shop mallet. The Craftsman appears to have a different configuration. Isthe removal process the same (i.e. striking a screwdriver with a mallet to loosen the piece)? It is not obvious to me that this piece is threaded onto the end of the shaft. Thank you.

Read More
Tom -
May 13, 2013
A:

Tom, The clutch in the video is slightly different from yours but the instructions are the same. Once you have the rope in the cylinder, the clutch can be removed. I have used the hammer and screwdriver method and I have also used a large pair of pliers to remove the clutch. Both work. Once the clutch is removed you can remove the starter housing to access the ignition module. I hope this is helpful. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
May 15, 2013
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show