Model #358360120 CRAFTSMAN Chainsaw, Gas

  • Chassis/bar/handle
    3 Results
  • Cylinder/muffler
    3 Results
  • Carburetor #530069722 (wt-391)
    3 Results
Find part by diagram >

Question and Answers

Q:

Chain is not oiling - what to look for? 358360120 Craftsman Chainsaw

A:

Thank You for choosing Sears PartsDirect.com. It is unfortunate to hear that you are having issues with your chainsaw and do understand your frustration. Glad to help out. Im looking at your model number 358360120 and If you have confirmed the outlet of the pump is cleared I suspect the pump is defective. To be sure, remove the pump and check the outlet of the oil tank. The oil should flow out of the tank. If the oil flows out the pump and tubing needs to be cleaned or replaced. If the oil does not come out use a wire to clear the tank outlet. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page.Here is a link for a video that may help with your troubleshooting. If you have further questions please resubmit your question for further information.
 
Thank you for choosing Sears PartsDirect.com.
 

Read More
Sherman_G_Wallace -
Sears Technician
July 03, 2014
Q:

Is it possible to install a Chainsaw chain backwards? How can you tell the correct way the chain goes? 358360120 Craftsman Chainsaw

A:

Yes it is. Refer to Pg 17 of your Owners Manual at link below.

Read More
Anonymous -
December 01, 2012
A:

Yes, it is possible to put the chain on backwards (I see it pretty often). When the chain is on correctly, you will notice the sharp edges pointing forwards on the top of the chain bar. So when you look at the cutters (the sharp edges) on the bottom of the chain bar, they will be pointing back towards you (as you stand to operate the saw).

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
December 02, 2012
See more answers
Q:

CHAIN SAW GAS LINE

A:

Replacing parts on your tool can be really tough without any owners manual. While you are waiting on an expert to answer your question, I found your owners manual in the manage my life website. I have tatted the link below. Hope this helps!

Read More
Dezeray -
September 08, 2012
A:

Thank you for your question.

I am sorry you are having a problem with the chainsaw. We do not have any written instructions for replacing the fuel line on chainsaws but I will try to help you. First, remove the air filter cover and the air filter. Then draw a diagram of how the fuel line is routed. I have also provided you with an image below showing the fuel line circuit. Then remove the all of the old fuel lines from the saw. When you are ready to reinstall the line cut one end so that it is tapered about an inch up. This will give you something to stick into the hole of the tank. Once in the hole reach into the tank with long forceps and grab the line and pull it through. Once you have it pulled in cut the pointed end off and install the filter. The line should be long enough so the fuel filter is on the bottom of the fuel tank. Then do the same for the return line. The only difference is the return line only has to be sticking in the tank about a half an inch.

I have found a few videos that I think might help you. Please click here to watch the first video . Then click here to watch the second video.

If you need further assistance, please feel free to reply below with more details.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

Here is a link to order any parts you need. Sears Parts Direct .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 09, 2012
See more answers

Top Parts