Model #358351701 CRAFTSMAN Chainsaw, Gas

  • Chassis/bar/handle
    3 Results
  • Cylinder/shield/crankshaft
    3 Results
Find part by diagram >

Question and Answers

Q:

Chainsaw carburetor adjustment

A:

Having to adjust Chainsaw carburetor can be quite a mystery to do without instructions. While you are waiting on an expert to answer your question, I was searching in the Manage My Life website and found a great link on how to adjust carburetor. I have attached the link below. Hope this helps!

Read More
Dezeray S -
December 14, 2010
A:

The information from the carburetor manufacturer shows the high/low speed screws to take a flat head screwdriver to adjust them. If yours does not look that way, you will need to get me the numbers off of the carburetor directly. That will be the only way I can find out what it is if it's different.

Thank you for using Manage My Life!

Read More
XX Wade_ -
Sears Technician
December 15, 2010
A:

Where can I get the "driver" too adjust the high- low carburetor adjustment screws on my new chainsaw model 358351701. Carburetor # 545070601. Screws are not flat head. � Screws are adjusted by a �female socket, many points about 24 or 30 points

Read More
Peter -
August 18, 2011
A:

The manufacturer does not make those tools available to the general public. The carburetor has a direct effect on the emissions from the engine and they feel like only a trained technician will be able to get the carburetor tuned correctly to work within the EPA recommendations. You may be able to find a local shop that will let you use their tools (at their shop) to make the adjustments needed.

Read More
XX Wade_ -
Sears Technician
August 19, 2011
A:

I do small engine repair out of my home for a very small community and have run across many different carburetor adjustment screw configurations. I take about a 4 inch thick wall rubber hose (vacuum hose) and push it over the screw to turn it. If the hose can't overcome the spring tension against the adjustment screw then I use a stout piece of plastic tubing that won't quite fit over the adjustment screw and heat it up until it's maluable and push it over the screw and let it cool down and then make my adjustments. One of these two methods has always worked for me.

Read More
Jack -
July 28, 2013
A:

Jack, Thank you for posting the tip on how to adjust the carburetors. I am sure this will come in handy for some of our members. Thank you for using Manage my life. Mark

Read More
Mark T -
Sears Technician
July 29, 2013
A:

Thanks Jack..... now when I FIND the screws..... LOL

Read More
Dan -
November 25, 2015
See more answers
Q:

saw blade 358351701 Craftsman Chain saw

A:

Thanks for the inquiry and for being a valued member.

The part number for the chain 71-3629 has been updated to an Oregon chain part number 91PX056G. That would be part number recommended to use at this time.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
February 25, 2015
Q:

adjusting the carberuator 358351701 Craftsman Chain saw

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your chainsaw. Upon researching model number358351701; the carb adjustment is for the idle speed. If it’s not getting enough gas it could be a fuel line issue or carb issue. Check the fuel lines for buildup. The carb could have internal build up. I linked the manual below. It has idle adjustments on page 20.

Thank you for choosing Sears. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
December 16, 2014

Top Parts