Model #358351580 CRAFTSMAN Chainsaw, Gas

  • Sears Model 358.351580
    3 Results
  • Cylinder
    3 Results
  • Carburetor Assembly Kit
    3 Results
Find part by diagram >

Question and Answers

Q:

Sears chainsaw model 358.351580

A:

Replacing the lines on the chainsaw may seem like a difficult task without the proper instructions.  While you are waiting for an expert to respond, I have added a helpful link that may provide information to assist you with your question.

Read More
Yadira B -
May 08, 2013
A:

Thank you for your question.   I am sorry you are having a problem with the chainsaw. We do not have any written instructions for replacing the fuel line on chainsaws but I will try to help you. First, remove the air filter cover and the air filter. Then draw a diagram of how the fuel line is routed. I have also provided you with an image below showing the fuel line circuit. Then remove the all of the old fuel lines from the saw. When you are ready to reinstall the line cut one end so that it is tapered about an inch up. This will give you something to stick into the hole of the tank. Once in the hole reach into the tank with long forceps and grab the line and pull it through. Once you have it pulled in cut the pointed end off and install the filter. The line should be long enough so the fuel filter is on the bottom of the fuel tank. Then do the same for the return line. The only difference is the return line only has to be sticking in the tank about a half an inch. I have found a few videos that I think might help you. Please click here to watch the first video. Then click here to watch the second video.   If you need further assistance, please feel free to reply below with more details.  If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears  technician.  Here is a link that will provide the nearest drop-off locations:  Sears Home Services.  Here is a link to order any parts you need. Sears Parts Direct .  Thank you for using Manage my life.  Mark T. 

Read More
Mark T -
Sears Technician
May 09, 2013
See more answers
Q:

i need a diagram to connect new fuel lines. 358351580 Craftsman Gas chainsaw

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Anna T -
April 30, 2013
A:

Thank You for choosing SearsPartsDirect.com

I can understand the confusion when replacing the fuel lines. I would be happy to help you with your repair today. We aren't given specific schematics for the fuel lines for some reason. But I have included a basic schematic provided by the manufacturer that is pretty easy to understand.

If you have further questions please let me know. I will be looking forward to helping you again. Thanks for choosing SearsPartsDirect.com

 

 

Read More
Desirea -
Sears Technician
May 01, 2013
See more answers
Q:

Chain Saw model 358-351580

A:

Good morning.... You are very likely correct in your suspicion. I have located a link that will address adjustments you might consider. But I would also encourage you to test your gas cap or replace it. An expert will be responding to you within the next two business days if not sooner. Have a nice day

Read More
Henry -
November 23, 2012
A:

This could very well be due to a fuel cap problem. When the saw dies, see if you can immediately restart it. If you can and it runs for a while longer than I tend to think the problem is something else. If the saw will not start after it dies, loosen the fuel cap for a few seconds and then tighten it back and see if you can start it up. If so, then it's very likely to be the fuel cap.

Also, if there is a primer bulb then it's possible that the primer bulb has a small crack/hole that would cause similar problems. But normally you would notice this when you prime the bulb up with fuel.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
November 24, 2012
A:

Now fuel cap has been replaced, same thing. I am sure the carb does not come adjusted ready to run. I would like to start over. How is the carb adjusted at first. Then I will fine tune it from there , I hope?

Read More
Duanes Repair -
November 27, 2012
A:

Turn the screws all the way in until they stop. Don't force them though, when they stop turning easily that's all the way. Now back them out 2 full turns and fine tune from there.

Read More
Wade_B -
Sears Technician
November 29, 2012
A:

Done all of that. Only runs on prime then stops. Wont start tilled primed.

Read More
Duanes Repair -
November 30, 2012
A:

Check the fuel lines to make sure they are not pinched anywhere. If they look good, swap them at the carburetor and see if the problem goes away. If they're on backwards it could cause this to happen.

It's also possible to have this problem if the spark arrest screen on the muffler is plugged up (though not common).

Read More
Wade_B -
Sears Technician
December 09, 2012
See more answers

Top Parts