Model #358351060 CRAFTSMAN Chainsaw, Gas

  • Replacement Parts
    3 Results
  • Motor Breakdown
    3 Results
  • Carburetor Kit #530-069703
    3 Results
Find part by diagram >

Question and Answers

Q:

craftsman chainsaw model 358.351060 358.351060

A:

All the way / as far as possible. - Previous Q & A's that may be of use in the future @ http://www.managemylife.com/mmh/questions?q=358.351060

Read More
Anonymous -
August 14, 2013
A:

Thank you for choosing SearsPartsDirect.com. I understand how important it is to be able to replace your primer line. This line needs to connect to the bottom of the tank to be able to siphon the very last bit of gasoline. I have included a link to our ManageMyLife page where you can view the manual you need to make any other repairs. Just click the blue link below to be taken to the page.
Owners Manual for Craftsman Chainsaw Model # 358351060
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using SearsPartsDirect.com.

Read More
Lokelani -
Sears Technician
August 14, 2013
See more answers
Q:

Gas Chainsaw basic mixture adjustments

A:

Having an important yard tool like a chainsaw not work properly can be a big hassle. I did some research on the problem for you and provided a link to a very similar question for the same model. I hope this will help and shed a little more light on the situation for you until the Expert responds in more detail within 24 to 48 hours.

Read More
Julio -
July 31, 2012
A:

Thank you for your question on the starting point adjustments on the Low and High speed jets for the carburetor.

With the limiter caps removed carefully screw in the Low and High speed jet screws until they stop. Be careful not to turn to tight as it will put a ring groove on the jet point and will no longer work well.

Then back both of the high and low screws out 1 1/2 turn counterclockwise and this should be your starting point if all the other factors are okay.

Because this is an older saw have you checked in the fuel tank to see if the fuel lines are still connected and in good shape?

When you get the saw running you can do some final adjustments on both the low and high speed screws.

The engine at idle should not turn the chain. You can affect this by turning the idle adjustment screw on the throttle plate.

The Low speed jet should be open enough so when you throttle up the engine it should stumble and die out.

To adjust the high you will need to throttle engine wide open and adjust the High speed screw so you will hear an alternating high low speed. If you only hear the high speed it will not have enough fuel and die out when cutting the log. Once you have the jet screws set replace the limiter caps to keep the needles from changing adjustments.

Please let me know how it went.

Sam A.

Read More
Sam A -
Sears Technician
August 01, 2012
See more answers
Q:

Chainsaw carburator fuel lines.

A:

I am sorry you are having some difficult replacing the fuel lines, these parts are very important and should be installed properly. I am adding a link below to help you with your project while you wait for your expert response.

Read More
Joseph P. -
March 20, 2012
A:

Thank you for your question.

I am sorry you are having a problem with the chainsaw. We do not have any written instructions for replacing the fuel line on chainsaws but I will try to help you. First, remove the air filter cover and the air filter. Then draw a diagram of how the fuel line is routed. I have also provided you with an image below showing the fuel line circuit. Then remove the all of the old fuel lines from the saw. When you are ready to reinstall the line cut one end so that it is tapered about an inch up. This will give you something to stick into the hole of the tank. Once in the hole reach into the tank with long forceps and grab the line and pull it through. Once you have it pulled in cut the pointed end off and install the filter. The line should be long enough so the fuel filter is on the bottom of the fuel tank. Then do the same for the return line. The only difference is the return line only has to be sticking in the tank about a half an inch.

I have found a few videos that I think might help you. Please click here to watch the first video . Then click here to watch the second video.

If you need further assistance, please feel free to reply below with more details.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

Here is a link to order any parts you need. Sears Parts Direct .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
March 21, 2012
See more answers