Model #3315 BLACK & DECKER Router

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Need part. Grill greese tray model #13723671310

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your grill. Upon researching model 13723671310:  I know it can be frustrating not to be able to order a replacement grease tray. Over time parts can be discontinued leaving us with the replacement, I apologize for any inconveniences caused by this part not being available. I have posted a link to the grills we currently have available, to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears

Read More
CarlosZ -
Sears Technician
May 06, 2015
A:

Same issue here. Grease tray rusted apart and fell out after one year of use. Looks like everyone else who purchased this has the same issue, and it's one of the few parts no longer available. You could clean up by producing a run of these in aluminum or stainless.

Read More
Frank -
June 14, 2015
A:

Others have had this problem and are saying to try this grease tray. I'm giving it a shot and will post back: http://www.searspartsdirect.com/nexgrill-grill-smoker-parts/718-059/0071/122/model-7200718/3315/1500125.html https://twitter.com/bwasson/status/590518068008263680

Read More
ANN MARIE -
October 26, 2015
See more answers
Q:

How old is my mower? 917255910 Craftsman Sears 18 h.p. garden tractor

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your lawn tractor. Upon researching model 917255910; based on the information provided, this model is from 1985.

I trust this information will help you, we appreciate your business thank for choosing Sears.

 

Read More
CarlosZ -
Sears Technician
April 15, 2015
Q:

chuck removal on old drill press mod3315-11970 31511970 Craftsman Craftsman 3/8 inch portable drill press

A:

I did some research on the drill and I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within two business days with detailed information. Thank you for using Manage My Life.

Read More
Joseph P. -
July 20, 2013
A:

Depending on the age of the Drill Press it may be a tapered chuck, meaning it's pressed in. Mine is a 1942 Craftsman and thats the way it's set up. I believe they were like that thru the 60's, possibly later.

Read More
softailgarage -
July 20, 2013
A:

Thank you for contacting SearsPartsDirect.com with your question about removing the chuck from your drill press. I can understand wanting to remove the part without damaging it. I will be happy to help you with this.

The chuck simply slides up over the end of the spindle assembly. There is not any kind of locking mechanism to keep it in place because all the load during use should be straight up against it. This prevents the chuck from coming down off the shaft. It is held in place with a slight interference fit. That means the shaft is slightly larger than the inside of the chuck so there is constant tension on the two surfaces when put together. That tension holds everything in place.

To remove the chuck, first lower it to the lowest positon. Then, use a wood or a rubber mallet and tap lightly in a downward motion on the chuck. If the chuck does not seem to move, you can tap it side to side to help work it loose. Be careful not to use too much force or you could damage the spindle assembly or score or bind the area where the chuck mounts.

If you are still not able to remove the chuck, I recommend spraying it with Boeshield. It is a combination of solvents, lubricants and waxes designed to work it way between parts and loosen them.

I have included the link for the chuck in case you need to replace it.

Chuck with key for Craftsman Drill Press Model  31511970. 

I hope this answers your question. If I can be of any further assistance, please respond to this thread. Thank you for choosing Sears, we appreciate your business.

Read More
Rachel Morgan -
Sears Technician
July 22, 2013
See more answers